All Installation Instructions for Samsung Washer WFJ1254XAA

Cold water valve not operating

Simple 2x cross head screws remove water inlet pipe, 2 internal pipes with spring clips, 2 electrical connectors test for leaks and operation perfect

Parts Used:

Cold Water Valve

Chris from Tyler, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

19 of 29 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Leaking water inlet hoses.

Removed the old hoses and screwed on the new hoses.

Parts Used:

Inlet Hose - 5 FT

Helen from NASHUA, NH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Washer making noise a snow smoking.

Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.

Parts Used:

Hex Head Bolt

Samuel from NEEDVILLE, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers, Socket set, Wrench set

9 of 22 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Door latch broke

Still have not received my part, been nine days since I ordered it. It was in a warehouse 600 miles from my house, as now travel over 3000 Thanks fed ex

Parts Used:

Door Handle Assembly

Guy from MYRTLE BEACH, SC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Cold water would not shut off during wash cycle

Unplug washer (got zapped when first fiddling with it).
Turn off cold water at source and unscrew hose from washer
Remove two small screws to remove top of washer
Uncouple contacts from old cold water valve
Remove 4 small screws holding valve to washer
Remove old cold water valve

Install new valve and reverse each procedure above.

Parts Used:

Cold Water Valve

Judy from MINNEAPOLIS, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old hot water inlet hose had budge at both ends.

Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.

Parts Used:

Inlet Hose - 5 FT

Jimmy from MEMPHIS, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Hot water would not shut off when wash temperature selected was hot or warm.

Disconnected power cord. Shut off water supply. Disconnected hot water supply hose. Removed top cover. Disconnected appliance connection to Hot Water Control Valve. Removed screws holding HWC valve. Removed existing HWC valve. Installed new HWC valve. Reconnected appliance connection. Reconnected water supply hose. Turned on water to check for leaks. Reconnected power supply. Started washer with hot cycle selected. Timed water fill time. Replaced top cover. Washed a load of whites in hot water. Installation and test complete.

Parts Used: