Models > WER211ES0 > Instructions

WER211ES0 Westinghouse Dryer - Instructions

All installation instructions for WER211ES0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WER211ES0
31-45 of 356
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Squealing sound Idler arm and pulley

  • Customer: Lewis from Thornton CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 11 people found this instruction helpful
This is actually a white consolidated IND. brand, but that wasn't on your list. Be sure to check your tensioner pully if you hear squealing coming from the dryer. I changed the felt ring and the support bearing before realizing that my pully bushing was the cause of the noise. If you have squealing then spray a little wd40 on the bushing and shaft, if the noise stops, then you found the smoking gun. Replace the pulley. Unhook the spring and it comes right off. No tools needed.

Old Dryer drum veins degraded and broke down.

  • Customer: Alfred from Loveland CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 8 of 11 people found this instruction helpful
I opened the top of the dryer to gain access to the outside of the drum. Then I removed the screws holding the old drum veins in using the electric drill with the nut driver attachment. Then I positioned the new veins in place on the inside of the drum and replaced the screws from the outside of the drum to hold the veins in place. Then I replaced the top and was ready to go.

This is the third repair that I have done using parts from parts select. the other two repairs involved replacing electrical parts. Specifically thermostatic controls or swicthes. I am very happy with the parts and the diagrams provided on your web site without wich I would have had to replace my dryer a long time ago.

The dryer drum wouldnt turn

  • Customer: Kara from Beckly WV
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 8 of 12 people found this instruction helpful
Had to pretty much disassemble the entire dryer. The schematics on the web site made it a snap to do. One word of advice. I you have to replace the rear drum assembly, the drum has to come out the front of the dryer. Part select made this a very positive experience.

dryer squeeking while in use

  • Customer: Paul from Fort Edward NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
unplug dryer. lift the top of the dryer up and back. Take the screws out holding the front panel on. One on each side. Disconnect wires from door open stop switch and take front panel off. Remove drive belt from around pulleys and lift drum up and forward out the front of the dryer. I had to replace the plastic and metal holder and the grounding ball also. Remove the shaft from the drum and put he new one on. Put the drum back in, wrap the belt around the drum and set drum in plastic holder. Then just reverse your steps. Fairly easy.

Wretched screeching noise

  • Customer: Paul from Broadalbin NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 6 people found this instruction helpful
Make sure you order a new belt and a new drum glide with the rear drum bearing assembly. If your bearing is worn out, so are the belt and drum glide!

1) Use a flat screw driver or putty knife to release the blind clips that hold the front side of the top of the dryer cabinet down
2) Swing dryer top up and remove two screws that hold the face of the cabinet.
3) Unplug the wiring harness and remove the cabinet face.
4) Remove the 3 screws that hold the drum to the bearing assembly (accessed from inside the drum. This makes it easier to remove the drum as the bearing assembly can be difficult to remove before you see how it snaps together
5) Reach under the drum and take the belt off the motor pulley, then remove the drum
6) Remove the old bearing assembly from the socket (slide up then out)
7) Remove the two screws that hold the bearing socket to the dryer
8) Fasten the new socket to the dryer (you'll need help doing this unless you have REALLY long arms because you have to reach inside the driver and the back of the dryer at the same time)
9) Grease the socket with the supplied high temp grease
10) Bolt the new bearing assembly to the drum and put the new belt around the drum
11) Put the drum back in and snap the bearing socket in and down
12) Guide the new belt around the motor pulley & tensioner
13) Glue the new drum glide / felt piece to the front cabinet
14) Put the cabinet back together

dryer drum squealing loudly!

  • Customer: john from waynesboro VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
THIS UNIT IS A STACKABLE WASHER&DRYER,SO FIRST PULL UNIT AWAY FROM WALL ATLEAST 4 FOOT.UNPLUG POWER CORD,THEN TAKE10 DAGREE FRONT PANEL OFF THEN THE CONTROL PANEL OFF AND UNPLUG THE 5 CONNETORS IF YOUR UNIT HAS THAT MANY,THEN LAY PANEL ASSIDE.TAKE DRYER DOOR OFF,MAKES IT EASIER WHEN PUTTING IT ALL BACK TOGETHER.NOW TAKE FRONT PANEL OFF AND THE DRYER LENT TUBE,NOW JUST TAKE THE 3 CENTER PHILLIPS HEAD SCREWS OUT AND SLIDE DRUM OUT.PULL UPWARD ON WHAT THEY CALL THE SHAFT WHICH HELD DRUM ON.NOW THESE ARE THE PARTS YOU SHOULD ORDER.BELT,GROUNDING BALL CLIP,GROUNDING BALL,DRUM SUPPORT BEARING,BEARING BRACKET,AND MOST IMPORTANT PART IS THE SHAFT.THE SHAFT IS UR INSURANCE FOR THE WHOLE JOB.USE A GOOD GREASE LIKE WHITE LITHIUM GREASE AND COAT THE SHAFT END AND THE DRUM SUPPORT BEARING.THE GREASE WILL CUT DOWN ON FRICTION FOR A WHILE,AND RE ASSEMBLE THE WAY YOU TOOK APART.REMINDER GROUNDING BALL GOES BEHIND DRUM SUPPORT BEARING NOT IN FRONT.GOOD LUCK AND PLEASE VACCUM.

door won't close

  • Customer: Dustin from Edmonds WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 6 people found this instruction helpful
. Supper easy I can't beleive it was over $20 for a little peice of plastic!!!

Dryer would not turn on

  • Customer: Michael from Erlanger KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
I contacted a company to come out and diagnose the problem. They informed me that the thermal limiter is bad and needed to be replaced for $15 for the part and $85 labor. I found the part on this site for about $10, and did the repair myself. The dryer was mostly dismantled so I pulled the drum back, and replaced the part. The tricky part was the pulley system was, so make sure you see it before hand or find a diagram online. Once that was figured out, I set the drum back up, greased and tightened the pulley, reattached the front of the washer with connections, and closed the lid.

Terminal block, and wires were dammaged/melted

  • Customer: Edwin from Eagar AZ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 7 people found this instruction helpful
Used nut driver to remove screw and cover from dryer cord terminal block, used screw driver to remove two screws securing old terminal block, cut dammaged wire and stripped wire back and crimped on new terminal connecter, replaced old terminal block with new one, replaced two screws, installed new cord, and replaced cover plate and screw.

Dryer was not drying clothes

  • Customer: Tina from The Plains VA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 9 of 16 people found this instruction helpful
Other repair stories about this product are very accurate and I used them to do the repair, so I see no need to be redundant.

I'd just like to draw attention to the following:
Disassembling the dryer is somewhat easy. Replacing the heating element is very easy.
Replacing the belt is very easy.

Replacing the drum bearing is somewhat difficult. I purchased a "T" screwdriver in order to get more torque on the screws. When I had the drum bearing in place and the screws partially inserted, I laid a piece of thick foam on the floor and set the drum, bearing side down, on the foam. It is very difficult to get enough tension on the screws to get them through the bearing plate, but setting the drum up this way at least allows you to use gravity to your advantage.

Thanks again to Part Select for making the part purchasing experience so effortless.

Thanks to other writers of "Repair Stories" for making my repair so easy.

Bearing Bracket Worn Out

  • Customer: David from Fairdale KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 7 people found this instruction helpful
Took off front panel, removed drum and replaced parts listed. A bit tricky to keep small parts in place. However, masking tape helped. Best of all was the online diagram of how the parts were assembled. In addition, taking step by step phone pixs aided in replacing parts since there was some down time between diagnosis and installation.

THUMPING NOISE, CLOTHES GETTING STUCK

  • Customer: LT Frank from Wacissa FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
UNPLUG, LIFT TOP, UNPLUG 5 WIRES, REMOVE 2 SCREWS, PULL DRYER FRONT AWAY WHILE SUPPORTING DRUM. REMOVE OLD GLIDES, SNAP IN NEW. REVERSE DISASSEMBLY PROCEDURE

Dryer would not start.

  • Customer: Onmi from Douglas GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 6 of 8 people found this instruction helpful
Unplugged the dryer from electrical socket. Vacuumed lint from dryer and exit hose. Removed top from dryer. Used pliers to remove the 2 wires from the thermal limiter. Used screwdriver to remove 2 screws that held the limiter in place.
Installed the new limiter, connected the 2 wires, plugged in the dryer's electrical connection, turned on dryer, and resumed my "washday chores".

Takes multiple cycles to dry clothes

  • Customer: Pamela from Portland OR
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 6 of 8 people found this instruction helpful
I don't think it would take others as long as it took me.
I had to take the drum out to get to the limiter. And my dryer is in a builtin housing with limited space in front of the dryer - so lots of manuevers to get access.

The limiter was very easy to find, thanks to diagrams on this site. The space between drum and limiter made it impossible to get to the limiter screws without removing drum. Found very helpful drum removal instructions on PartSelect here:

http://www.partselect.com/PS1148434-Frigidaire-134503600-Dryer-Drum-Belt.htm?SourceCode=13&ModelNum=FSE748GFS0

Great site - thank you.

The rear drum hitch was sheared off

  • Customer: Nathan from Clarence IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 5 of 5 people found this instruction helpful
I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the birthday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.
All Instructions for the WER211ES0
31-45 of 356