Models > WER211ES0 > Instructions

WER211ES0 Westinghouse Dryer - Instructions

All installation instructions for WER211ES0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WER211ES0
196-210 of 356
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loud Noise in dryer

  • Customer: Natalie from Jasper TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
Removed the top and front of dryer. Removed the old bearing and held the new bearing in place while my husband tightened the bearing into place......easy......now the dryer runs quiet again.

noisy

  • Customer: John from OFallon IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 3 people found this instruction helpful
removed drum & replaced bearing, belt & shaft - reassembled

Timer kmob broke off of dryer

  • Customer: Karen from Plainfield NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
I pushed the knob onto the metal dryer piece. It was repaired in less than 10 seconds. Also I was very impressed by the fact that I ordered the part on Thurday morning and I had the part the very next day. I am a happy customer and will recommend parts select.com to others

strike broken

  • Customer: Linda from Batesburg SC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 10 people found this instruction helpful
popped in one in

door handle an screws missing

  • Customer: gary from hope AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 18 of 184 people found this instruction helpful
doo handle snapped in place an replced screws that were missing

lint filter bent

  • Customer: Ellen from Baltimore MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 19 of 222 people found this instruction helpful
Vacuumed lint and inserted new filter.

squeaking, got worse and worse

  • Customer: Jon from Brooklyn Center MN
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 2 of 216 people found this instruction helpful
Printed out what others said, took pictures of everything as I took it apart. I went slow. It all worked the first time I put it back, WOW!
Be careful if you are working with a gas line, use two wrenches to disconnect, less stress on the pipe.

took 3 cycles to dry made alot of niose growling and rumbling

  • Customer: Joseph from Indianapolis IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 20 of 338 people found this instruction helpful
first turn off breaker and unplug dryer !!! popped open top of cabinet pushing in on 2 clips with butter knife then removed the front panel,2 phillips screws then pull out on top until 2 spring clips pop out, remove 2 wires from door switch move to side. remove motor access panel lower rear 2 phillips screws. unplug wire clip from motor, push belt tensioner to right,undo belt from motor pulley and tensioner , then undo 1 snap clip from cradle holding motor go to front of dryer remove 2 phillips screws from blower houseing to base. unscrew senser from front of houseing then carefully lift slightly on front of drum and pull blower houseing and motor out as one. hold motor shaft still and unscrew blower wheel from motor shaft, install new motor do not overtighten blower fan you will break it slide belt off drum put new belt on makeing sure grooves are against the drum. slide motor assembly back in put motor back in cradle in rear and reinstall clip, screw down blower assembly in front, reinstall belt on motor pully and tensioner and clip wires back on motor. put front panel back on making sure not to damage felt on front of drum, rotate drum by hand several full turns clockwise to make sure belt tracks properly, reinstall wires on door switch and all screws and rear cover plug in turn breaker back on and test

they where just wore out.

  • Customer: Cindy from Ringgold PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 11 of 442 people found this instruction helpful
Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.

Dryer drive belt broke

  • Customer: Steve from Birch River WV
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 23 of 621 people found this instruction helpful
I opened top section with a screwdriver, pushing in the release.
I opened front panel with door with screwdriver pushing in the release.
I lifted drum out through the front.
I replace the Idler Arm assembly.
I greased the rear drum bearing race.
I vacuumed out and cleaned blower and dryer area.
I put the new belt on the drum, reinstalled the drum.
I put belt around drive motor and Idler arm assembley.
I put front panel with door back on.
I put the top panel back down and snapped into place.
Tested dryer, job done!

rear support bearing squeeking

  • Customer: Paul from Mont Pelier VT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 21 of 674 people found this instruction helpful
removed top and front of machine. removed drum. replaced shaft, bearing bracket, and support bearing from inside. replaced grrounding ball and clip from outside. reassemble.
this should be available as a kit, and should include high temp grease to put in bearing bracket

Due to weather exposure, the handle fatigued and broke in several parts.

  • Customer: Sean from Sacramento CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 57 of 985 people found this instruction helpful
You simply pry the old handle off with a flathead screwdriver, and then line up the new handle and snap it into place. It took less than 30 seconds! A breeze.

Heating Element burned up/ No Heat

  • Customer: Ashley from Ripley WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled front off dryer, popped the top up, took belt off pulley, pulled drum up and out just far enough to pull element out and put new one in. Very easy and quick. PartSelect always sends good quality parts and very quickly. I will use them for all my repairs.

Dryer was making a squealing noise

  • Customer: Trever from Vancouver WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair video from PartSelect.com was excellent in describing how to fix the dryer. All of the parts were included in the replacement kit, including the screws and ball bearing. I was very impressed with the quality of the kit and the video. A $25 kit probably saved me hundreds in repair cost and saved me from having to buy another dryer. Here's to another 14 years of use!

Loud Racket couming from the bearing casing

  • Customer: Jason from Champaign IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered the part from PartSelect.com. It came in a couple of days, which was nice. My wife was all over me to fix the dryer, or buy a new one. Needless to say, I didn't think the old one was done. The bearing assembly had an instructional video. This provided easy to follow instructions, and simple advice even I could follow. Everything went well, and the dryer is now quietly running as good as new. Awesome website, and the customer service is excellant too. WE use PartSelect.com at work all the time. Im a property manager, and the parts and advice save us thousands every year. Thanks guys!
All Instructions for the WER211ES0
196-210 of 356