Models > WEQ332HS0 > Instructions

WEQ332HS0 Westinghouse Dryer - Instructions

All installation instructions for WEQ332HS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WEQ332HS0
376-390 of 404
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dryer starter knob broke

  • Customer: Alan from South Lyon MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
put new knob on the shaft, took less than 5 seconds.

dryer was making a shrill noise

  • Customer: Mike from Goldonna LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed the front then removed the belt that turns the drum pulled the drum strait up from the top then removed the bushing from the back wall put the new one in I also put A little grease in the new bushing to keep it from wearing installed the drum and front. realy easy. I'm A Instructor at A technical collage in Winnfield Louisiana and I used this as A project for my students.

drum belt

  • Customer: MANUEL from SAN JACINTO CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
so easy my daughter installed it the video was very helpful

Loud screeching noise, barrel turned OK and Heater worked

  • Customer: Ellen from Willits CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
I took the lower back panel off. Loosened the center bolt and took off the old Idler pulley. It looked brown in the middle and didn't roll well. But I wasn't sure if that was it, because the noise was so loud and sounded metal on metal. So I checked everything and vacuumed everything. After I got the new part it took me about 5 minutes to put the new one on. And dryer works fine. Thanks for the quick response and I saved about $200.00!

Dryer had no power. After doing quick troubleshoot determined Thermal Limiter was the problem

  • Customer: Darrell from McCalla AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed top from dryer. Saw I could get to Limiter without removing dryer drum.Removed Limiter with phillips head screwdriver and wires with needle nose pliers. Replaced wires and secured Limiter to dryer works like a new one.

replaced rear drum bearing

  • Customer: chuck from carroll NH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
the repair when ok the only problem I had was installing the small white plastic piece in the back without losing the ball bearing .and I also vac up everything inside as well lot of lint

My dryers was making a loud thumping sound. Like it was off balance.

  • Customer: Dennis from Maple Shade NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I Took the front off and saw the cushion was gone around the drum and glids were worn down. I ordered both parts . It took 5 minutes to glue the cushion back on around the drum and 2 minutes to snap the drum glids on.But what I couldnt believe was the amount of lint that was all over the inside of the dryer.I would suggest to anyone to take the dryer front off once a year and clean it all out . I now understand fully why there are dryer fires.But the fix was cake and it runs like new.

Dryer runs but does not produce heat, bad heating element

  • Customer: George from Worcester MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged the dryer from the power outlet and removed two screws from the back of the top cover and removed the cover. Then I laid the dryer down on its back for easy access to the screws on the bottom of the front side. I then removed two screws from the front bottom cover to clear the way for two more screws for the front main panel and door. Then I removed those two screws that attach the front panel and door to the dryer from the bottom of the dryer front. I then stood the dryer back up on its 4 pegs. I removed the top 4 screws connecting the control panel to the cross bar on top. Then I removed the two screws from inside the dryer accessing them from the top of the dryer, holding the front panel. With little and gentle force I pulled the front panel and door from the dryer housing, making sure not to loose the 4 snaps that come off with it. I removed two screws from the access panel to get access to the pulley in the lower back of the dryer. I loosened the tensioner by pushing it to the side and pulled the belt off the pulley. Next I needed to remove the drum which is connected by three screws in the center of the inside of the drum to a small plate on the outside that is attached to a ball that goes into a grease box. I then wiggled the drum out of the dryer. With some force I pushed the plate upwards to disengage it from the grease box and removed it. I unplugged the electrical wires connected to the thermostat and element. I then removed 4 screws from the back of the dryer that hold the heating element housing and removed the housing. I replaced the heating element and housing and the belt and put the dryer back in reverse order.

loud noise at back of dryer

  • Customer: sam from prattville AL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
i watched the video that is furnished at parts select, it was very useful in doing this repair. i would strongly recommend watching this as i did install the ground bearing wrong to start with,and restringing the drum belt is something you have to feel as your installing it back in place so the video is useful for that as well. my repair was on a front load dryer made by Frigidaire,

Squeaky noise from rear of dryer

  • Customer: Kenneth from Pensacola FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug dryer, remove rear access cover and removed belt from pulley. Remove bottom cover on front of dryer, remove top of dryer, unplug harness to control panel and remove front door assembly. Remove screws from drum to bearing assembly. Removed drum and belt removed bearing assembly by lifting up and out of the bearing socket. Vacuumed all the lint. Removed the bearing socket, installed all parts and covers in reverse order.

There were several pieces broken around the band and as the drum turned, clothes would catch the cuts and slice right though like a razor blade

  • Customer: David from Alto TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Take the top off the dryer. Once it's off, start inserting the bands from the inside. From the top or inside, control and move the drum as needed to insert band in place. Once band is in place, and holes line up, press down till you hear it snap in place. Repeat process with second band.

Banging coming from the dryer with light loads or when clothes we close to being dried

  • Customer: Bryan from Rome NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Use flat blade to compress clips so top could be raised. Use Philips to remove 2 screws holding front on. Popped front off and then removed old worn and broken glides. Had to lift the drum slightly when placing the front back on. Screwed in the 2 screws to hold the front on. Lowered and locked top. Be careful not to pinch any wires..

rear bearing on dryer was squeeking badly

  • Customer: Douglas from Hudson Falls NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed instructions I found on u-tube to remove the drum and belt and access the bad bearing and change it. The instructions were quite good other than needing to remove a small panel on the back of the dryer to pull the belt around the tensioner.

Dryer made extremely loud rhythmic screeching sound when running.

  • Customer: Paul from Holly Springs NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
DIsassembled the dryer by removing the top piece first. Removed the kick panel and the two screws on the bottom of the front panel. Disconnect the 2 wiring harnesses then remove the remaining 6 screws that you can see from the top. If possible, have someone support the front panel as you undo the last couple screws. Remove the plate on the rear lower right side to expose the pulley and belt. Pull on the tensioner while gently pulling the belt off the pulley and tensioner. Lift the drum up quick and hard to separate the ball shaft from the bearing holder. Remove drum by taking it out through the front opening. Replace the ball shaft on the back of the drum. This is much easier if you have an extra set of hands. At this point, vacuum out as much lint as you can. There is a white container attached to the front panel, vacuum this too. THere was several inches of lint build up that had made it past the screen. Replace the bearing, ball retainer, and ball bearing on the dryer. Grease the ball and retainer and reinstall the drum. SInce I was replacing the bearing, I went ahead and replaced the belt too. Reposition the belt on the pulley and tensioner. Spin it a little to make it is on the right place. Reassemble the dryer. This is the first time that I have done a repair of this sort and it turned out to be a lot easier than I thought. Two people would have made it even easier and faster.

Very loud squeaking

  • Customer: daniel from santee CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Followed the video, it was good, the instructor's tips were useful and time saving.
All Instructions for the WEQ332HS0
376-390 of 404