Models > WEF365BHDB > Instructions

WEF365BHDB Westinghouse Range - Instructions

All installation instructions for WEF365BHDB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WEF365BHDB
46-60 of 610
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F3 Error

  • Customer: Jonathan from Lewisburg PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 6 of 9 people found this instruction helpful
I removed the back panel, about 6 screws, then found the probe which was attached by 2 screws. Unscrewed them and unplugged it. Plugged the new one in and replaced all the screws. The oven works like a charm now! No more F3 errors!

error sensor on display when oven was used

  • Customer: James from Clarence NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 9 people found this instruction helpful
I looked up the error code on line and found it was likely a faulty oven temp sensor. I was able to find the part and diagram at partselect.com and placed an order. The probe was in stock and arrived within a couple days. The repair took only about 20 minutes and works fine now. Thanks for your help partselect.com!
Jim

Draw glide broken off bottom drawer.

  • Customer: Kathleen from fall river MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
New part arrived, opened pkg., pulled drawer out...snapped in new parts....DONE!! Saved myself $100.00.

The latch for locking the oven during the self-cleaning cycle was broke and would not lock

  • Customer: carlton from crescent city FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I first lifted the top of the stove up where the burners are then removed 7 philips head screws plus the 2 screws that hold the latch in place, which is just above the oven door. I pulled the old latch off the rod that goes to the lock motor.I hen put the new latch in and replced all the screws. Turned the self-cleaning cycle on and it worked perfectly.Thanks to the help of repair guy at Parts Select and the pictures made the repair simple and fast. Thank You Patrs Select

Electric burner switch shorted out.

  • Customer: Armando G from Alice TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
First I unpluggd the range and removed the back cover using a nut driver. Then I removed the knob by pulling (using a little force),Not very hard to do. I uscrewed two screws that hold the switch from the front of the range. Then I pulled the switch out about three inches and used pliers to disconnect the wires one at a time and connect them to the new switch. finally I finished the installation by reversing all the steps. Total time to install the switch took approximately 5(five) minutes.

Oven door inner glass cracked after cleaning

  • Customer: Lisa from Erial NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
The repair went relatively easy especially after reading that another homeowner found the door to be "spring loaded". I was prepared and made sure I held onto things tightly.I removed the screws as I came to them and carefully removed the other 3 pieces of glass, finally reaching the inner panel. Putting that in and holding it as I put the next piece back was the most difficult. Once that was in place, the rest was just a matter of redoing what I undid. Needless to say, I was a bit nervous the first time I used the oven. No problems though, works like a charm! Thanks!

switch not always turn off

  • Customer: Jerrold from San Marcos TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 4 people found this instruction helpful
Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

Broken door glide

  • Customer: Michael from Signal Hill CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
snapped the new piece of plastic in its place and ta da, its fixed.

Broiler element burned out

  • Customer: Merlin from Newport News VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Very important first step: Turn off the circuit breaker for the range or disconnect the power cord.
I removed the oven door to make it easier to access the back of the oven; remove two screws and the door lifts off of the brackets. Removed a screw from the top of the oven that secures one end of a wire that supports the broil element. Removed two screws that secure the broil element plate to the back of the oven. Pulled the element forward exposing the end terminals and wires. The wires are connected to the element by spade connectors. Used long nosed pliers to remove the connectors from the element. Pushed the connectors on to the new element and stuffed the ends of the element and wires back through the opening and the insulation. Reinstalled the two screws holding the element in place and the screw holding the wire in place across the top of the oven. Reinstalled the door. Took less than 30 minutes.

cook top was broke

  • Customer: Ed from Bellefontaine OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 9 people found this instruction helpful
we removed the old cook top sixteen screws and four bolts was removed put the new top back on and put all the screws and bolts back in job done

Large burner would turn on high and not cycle off

  • Customer: Kevin from Nashville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
TURN BREAKER TO RANGE OFF! Move range out to access rear of the unit. Remove 6 screws to gain access to rear of controls panel. Pull knob off switch. Remove 2 pan head Phillips screws to take switch out. Lugs not in matching pattern but are clearly labled, swap wires one at a time. Reverse the disassembly steps and push the range back in place. DONE

Element burned out

  • Customer: James from Colonial Beach VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 3 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. The I reversed the process to install the new element which was exactly the same as the burned out one.
At first I was on the verge of replacing the whole stove before I decided to google " range heating elements". I ordered the part from your company and it arrived promptly.
Needless to say, I am thrilled that I don't have to buy a new stove. This one now works perfectly!

Bake element bad, broiler element OK.

  • Customer: Gerry W. from Oxford IA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 9 people found this instruction helpful
Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!

Overlay was cracked, drawer glide missing

  • Customer: Michael from Anchorage AK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 9 people found this instruction helpful
Overlay replacement is easy; 1st remove two screws that hold panel to top of stove (philips screwdriver) and lift up off of lip at very top, 2nd remove two screws that hold control to panel (nutdriver or square drive screwdriver), 3rd peel old overlay from control panel face (make sure you get any & all little bits so new overlay sits flush), 4th peel backing from overlay and position over control panel (peel protective film from face of overlay as well), 5th reposition control panel and reinstall two screws removed in step two above, lastly reposition top panel on stove and reinstall the two screws removed in step one above.
Drawer glide just snaps into place on the lower rear corners of drawer, then you slide drawer back into place.

Broken glass inside door of oven

  • Customer: Janice from Brooklyn NY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 5 of 10 people found this instruction helpful
First took apart oven door. then took out broken glass and replaced with new glass.Put everything back together done.
All Instructions for the WEF365BHDB
46-60 of 610