Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WEF303PHDA

WEF303PHDA Westinghouse Range - Overview

Get Parts and Repair Help for WEF303PHDA

If you know the range repair part you need, you can browse the list of all parts on the WEF303PHDA, or you can search by name or part description. You can also find your part by where it is located on the WEF303PHDA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for WEF303PHDA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.15

Bake Element - Push On Terminals - 240V

This bake element is used in electric ovens and ranges. It can be found in the bottom of the appliance. It supplies the heat required for the baking function. If your element is no...

$3.13

Drip Bowl - 8"

This chrome drip bowl is designed for use with electric cooktops and ranges. It sits beneath the 8-inch surface burner element. It catches any drips or spills coming from the cookware on your burner. Because the cooktop is a high-traffic area of the kitchen, these bowls often get damaged, or get so dirty they can no longer be adequately cleaned. If that is the case, this is the replacement part you need. The drip bowl is sold individually. At the widest point this part has a diameter of approximately 10 inches. When replacing this part you need to remove the burner element. While you have it out we recommend inspecting the terminals and the element for any corrosion, arcing, or discoloration. Any of those things could be a sign of a bigger problem, and it indicates that the element and terminal block should be replaced.

$3.23

Chrome Drip Bowl - 6"

The drip bowl function is to catch grease and spills that come from cooking on your stove top. They are located under the heating elements. Drip bowls are often neglected and can b...

$6.59

Terminal Block Kit

This part connects the wire harness to the surface element and is used for ranges. The kit includes interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing, and wires. If your range/oven is having symptoms such as burner not heating, heating elements not working, burning smell, or if the oven is making a buzzing noise then this could be the solution. The tools needed to replace the kit are wire strippers, a heat gun or hair dryer, and #1 square heard screw driver. Refer to the installation/instructional video for further guidance to accurately replace the element.

$11.36

Surface Element - 8" - 220V

If the burner element on your range will not heat up, or is damaged, it may need to be replaced. This part is 8 inches in diameter, and should not be confused with the smaller 6-in...

$20.52

Surface Element - 6"

This part is sold individually. This is a part for your stove top. The surface element is what your cookware sits on. The element supplies heat at varying temperatures. This may need to be replaced if the coil has shorted out or the terminal block shorted, and this caused the connectors at the end to burn out. The element is set in place by springs. You will need to push the springs in to release the old element. Make sure the drip bowl is lined up with the terminal block and press the new element into place.

$3.52

Main Terminal Block Kit

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryer...

$22.37

Burner Switch Kit

This is a burner switch kit, also known as the surface element control switch repair kit, for ranges. This burner switch kit sends voltage to the surface element coil and it controls the stove top surface burner. If the following symptoms occur, installing the switch could be the solution to the problem: surface element not heating, overheating, or inconsistent heating. Usually, if the element is not defective, that is a sign there is an issue with the switch. The kit comes with several insert sizes, and includes screws as well. The tools needed for this project are a nut driver, pliers, and screwdrivers.

$18.11

Broil Element

This broil element is found on the roof of the oven.

$5.38

Indicator Light Lens

This is a red indicator light lens for an oven that covers the indicator light for the surface element. The indicator light signifies when the element is on and heated. This part is sold individually. It is recommended to check other red indicator lights in case they need to be replaced because they often wear at the same rate. It is difficult to see the light without the red lens. This part does not include the light. If your light does not illuminate, you may want to consider ordering the light as well. Tools required for this repair are a 1/4 inch nut driver and a stubby Phillips screwdriver.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven woudn't heat

  • Customer: David from Shawnee, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1108 of 1149 people found this instruction helpful
1. Removed two screws, pulled out the element, voltage tested the element and determined it was an open circuit (bad element).
2. Ordered the part from partselect.com
3. Disconnected element, connected the new one, and screwed it back in. read more

Element cracked in two pieces

  • Customer: Michael from Green Bay, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 713 of 808 people found this instruction helpful
Shut off circuit breaker to stove and collected the tool from the basement. Turned on flashlight. Unscrewed the two hex nuts from the old element/back of the oven. Slid the old element prongs out of the back, exposing the connecting wires. Pulled the connecting wires off of the old element, carefully, so that the connections wouldn't come off of the w... read more

oven did not heat

  • Customer: jack from chambersburg, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 415 of 425 people found this instruction helpful
removed screws pulled element out. removed wire from old element replaced with new element.very easy read more