Models > WED6600VW0

WED6600VW0 Whirlpool Dryer - Overview

Get Parts and Repair Help for WED6600VW0

If you know the dryer repair part you need, you can browse the list of all parts on the WED6600VW0, or you can search by name or part description. You can also find your part by where it is located on the WED6600VW0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for WED6600VW0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$11.46

Thermal Fuse

This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins...

Order within the next 4 hrs and your part ships today!
$52.07

Heating Element - 240V 5400W

This element is strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer.

Order within the next 4 hrs and your part ships today!
$34.44

Maintenance Kit

This kit comes with one multi-rib belt, two drum support rollers, one idler pulley, four tri-rings, and one clip. This part can be used with both gas and electric dryers. NOTE: Th...

Order within the next 4 hrs and your part ships today!
$3.69

Door Catch

This part helps to keep the door closed when the machine is in use.

Order within the next 4 hrs and your part ships today!
$11.01

Drum Support Roller

Sold Individually. Most dryers require 2. Tri-rings sold separately.

Order within the next 4 hrs and your part ships today!
$20.35

Internal-Bias Thermistor

Part may differ in appearance, but functions the same as original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

Order within the next 4 hrs and your part ships today!
$3.54

Leveling Foot

Sold individually.

Order within the next 4 hrs and your part ships today!
$5.14

Tri Ring

Sold individually.

Order within the next 4 hrs and your part ships today!
$4.54

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

Order within the next 4 hrs and your part ships today!
$17.27

Idler Pulley Arm with Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum. This arm is what attaches to the idler pulley wheel.

Order within the next 4 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer motor runs, but no heat

  • Customer: Gadi from Irvine CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 1373 of 1502 people found this instruction helpful
To reach the heating element you only need to open the back cover of the dryer (about 8 nut-head screws). Remember to disconnect the power.

To remove the heating element there are two small nut-head screws. Remove the two electric wires. Then you can pull the heating element away.

You can check the heating element with an ohm-meter or v... read more

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1278 of 1465 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

No heat but would run otherwise

  • Customer: Dana from Grassvally CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 524 of 538 people found this instruction helpful
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and didn't take but 15-20 m... read more