Models > WDP350PAAW2

WDP350PAAW2 Whirlpool Dishwasher - Overview

Get Parts and Repair Help for WDP350PAAW2

If you know the dishwasher repair part you need, you can browse the list of all parts on the WDP350PAAW2, or you can search by name or part description. You can also find your part by where it is located on the WDP350PAAW2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for WDP350PAAW2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.76

Rack Track Stop

Used for upper dishrack track.

$36.26

Heating Element

This dishwasher heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher and also comes with the 2 washers.

$3.96

Rubber Washer

Sold individually. Used with the heating element.

$23.43

Faucet Adapter

Used with some portable dishwashers and washers. NOTE: As per the factory, this is used for faucets with inside or outside threads. For female connection (outside) just remove the washers.

$50.96

PUMP-DRAIN

$2.70

Hose Clamp

$5.25

Touch-Up Paint - White

$16.83

High Limit Thermostat

This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element.

$144.23

Upper Dishrack Kit

The dishrack kit comes with the dishrack, rollers, adjustable tines, and clips. Must be assembled. Note: This part has been redesigned by the manufacture. Blue is no longer avail...

$48.85

VALVE-INLT

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dishwasher not draining after wash cycle

  • Customer: Andrew from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 95 of 105 people found this instruction helpful
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
... read more

Heater element broken.

  • Customer: Dennis from Sedro Woolley WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 53 of 58 people found this instruction helpful
Step 1: Remove the screws in the bottom of the countertop.

Step 2: Remove the screws holding the bottom kickplate.

Step 3: Loosen leveling legs.

Step 4: Pull dishwasher out of hole.

Step 5: Unlplug dishwasher.

Step 6: Disconnect wires from bottom of element in back.

Step 7: Remove plastic nuts... read more

UNIT WOULDN'T WORK. "CLEAN" LIGHT BLINKING

  • Customer: PAUL from ESTES PARK CO
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 33 of 46 people found this instruction helpful
The unit had power, but the controls would not work. The "Clean" light was blinking. I first replaced the control unit, no help. I then used the "Just Ask" and was told the problem was the heating element and/or the Hi-Temp thermostat. I replaced both those and used the re-set code pushing the "Hi-Temp/Air Dry, Hi-Temp/Air Dry" buttons. That did it. Easy par... read more