Models > WDG547PBS1

WDG547PBS1 Frigidaire Dryer - Overview

Get Parts and Repair Help for WDG547PBS1

If you know the dryer repair part you need, you can browse the list of all parts on the WDG547PBS1, or you can search by name or part description. You can also find your part by where it is located on the WDG547PBS1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for WDG547PBS1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$18.79

Rear Drum Bearing Kit

This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant and installation screws.

Order within the next 8 hrs and your part ships today!
$18.16

Upper Drum Glide

Front upper felt glide pad with 3 nylon glides - includes adhesive.

Order within the next 8 hrs and your part ships today!
$2.83

Drum Support Bearing

This part attaches onto the inside of the rear panel of the cabinet.

Order within the next 8 hrs and your part ships today!
$25.18

Door Catch

This part helps keep the door closed while the machine is running.

Order within the next 8 hrs and your part ships today!
$16.61

'M' Series Ignition Coil Kit

This ignition coil kit contains two coils. One is a two wire secondary coil, while the other is a three wire booster coil. Both should be used together in your gas clothes dryer.

Order within the next 8 hrs and your part ships today!
$7.32

Door Strike

"Male" piece of a dryer door closing mechanism.

Order within the next 8 hrs and your part ships today!
$8.70

Bearing Bracket

This part mounts on the inside of the rear cabinet.

Order within the next 8 hrs and your part ships today!
$31.02

Seal

Adhesive is sold separately.

Order within the next 8 hrs and your part ships today!
$7.29

Grounding Ball

Sold individually.

Order within the next 8 hrs and your part ships today!
$21.56

Igniter

This part ignites the gas within the dryer. Be sure to not handle this igniter by the gray part as it is very fragile.

Order within the next 8 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Clothes getting scorch marks, drum noise

  • Customer: Matthew from Portland OR
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 484 of 488 people found this instruction helpful
First and foremost, I read the repair reviews here at parts source and found that a) Other people had the same symptoms, b)following their repair tips made it super easy.
What I would add to previous reviews is to pull the front off or the little acces grill in back and check to see what kind of belt you have. According to the model #, It showed the wi... read more

Loud Squeaking

  • Customer: Frank from Boyertown PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 261 of 269 people found this instruction helpful
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Acc... read more

Drum glide wore down and caused close to get stuck between drum and front panel.

  • Customer: William from Boise ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 167 of 232 people found this instruction helpful
Unpluged dryer. Removed the top of dryer by pushing in a retaining clip on both sides of the front lip with a screw driver. Remove the two screws on both sides of front panel. These screws are square head or phillips #2. Unplugged the wiring harness to front panel (make sure power has been disconnected). Support drum and lean front panel away from dryer ... read more