Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WDF530PSYB5

WDF530PSYB5 Whirlpool Dishwasher - Overview

Get Parts and Repair Help for WDF530PSYB5

If you know the dishwasher repair part you need, you can browse the list of all parts on the WDF530PSYB5, or you can search by name or part description. You can also find your part by where it is located on the WDF530PSYB5 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for WDF530PSYB5 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$38.91

Heating Element

This heating element is designed to monitor and control the heat of the water that enters the dishwasher. It is located at the bottom of the dishwasher. If your dishwasher is not d...

$11.43

Mounting Bracket

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

$16.83

Rinse Aid Cap

The rinse aid cap (sometimes referred to as the dispenser cap), covers the rinse aid dispenser on the dishwasher door. If your dishwasher will not dispense detergent, or it is leak...

$30.20

Drawer Track

$4.89

Rubber Washer

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where...

$65.70

Drain Pump - 120V 60Hz

This drain pump is used in dishwashers to remove water from the dishwasher tub. If the impeller in the dishwasher is damaged or the motor has been shorted out and will not drain, it is possible the body is cracked, causing leakage. To prevent this from happening, replace the drain pump. The tools needed for this installation are: Phillips screwdriver, 5/16 inch nut driver, 5/8 inch wrench, and a flathead screwdriver. Remember to unplug your dishwasher from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions.

$4.40

Friction Sleeve

This part helps to keep your door quiet when it opens and closes.

$17.63

High Limit Thermostat

This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element.

$27.52

Door Latch - Black

NOTE: This part has been redesigned, it may appear different but will still function the same as the original.

$16.00

Retainer Clip - Black

This part is used to hold the access panel in place. Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dishwasher not draining after wash cycle

  • Customer: Andrew from Alexandria, VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 298 of 332 people found this instruction helpful
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
... read more

Heater element broken.

  • Customer: Dennis from Sedro Woolley, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 129 of 140 people found this instruction helpful
Step 1: Remove the screws in the bottom of the countertop.

Step 2: Remove the screws holding the bottom kickplate.

Step 3: Loosen leveling legs.

Step 4: Pull dishwasher out of hole.

Step 5: Unlplug dishwasher.

Step 6: Disconnect wires from bottom of element in back.

Step 7: Remove plastic nuts... read more

latch on dispenser cover broke

  • Customer: Craig from Austin, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 114 of 126 people found this instruction helpful
Printed door assembly parts list and photo from KitchenAid website. (With the absence of instructions, it was a big help.) Remove door cover. You'll need a star driver bit. Remove the old dispenser. Note how the metal clamp and black cover sheet are positioned. Install the new dispenser. Insure the wiring harness is snapped in place. Replace the door... read more