The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
$7.71
In Stock
Order within the next 10 hrs and your part ships today!
This manufacturer-certified heating element is used to create heat during the dry cycle and increase water temperature during portions of the wash cycle when certain options are selected. If your dish...
$66.15
In Stock
Order within the next 10 hrs and your part ships today!
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
$10.04
In Stock
Order within the next 10 hrs and your part ships today!
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Order within the next 10 hrs and your part ships today!
This water inlet valve should be located behind the lower kick plate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.
$64.02
In Stock
Order within the next 10 hrs and your part ships today!
This filter works with the water pump in your dishwasher. It prevents debris from entering the pump and causing damage. As a result, the filter can occasionally become clogged or damaged, and will nee...
$58.02
In Stock
Order within the next 10 hrs and your part ships today!
This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating element.
$20.71
In Stock
Order within the next 10 hrs and your part ships today!
This is a lower spray arm for a dishwasher. The lower spray arm allows water to be spread evenly throughout the dishwasher tub with the proper force so dishes come out clean. This spray arm is gray in...
$60.79
In Stock
Order within the next 10 hrs and your part ships today!
Order within the next 10 hrs and your part ships today!
Questions And Answers for WDF330PAHB4
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Steven
October 18, 2021
Water does not get hot, could it be heating element
For model number WDF330PAHB4
Hello Steven, Thank you for the question. We suggest testing the element. To test the element, locate your dishwasher's heating element. Open the dishwasher door and look into the tub. It is the thin, circular tube at the base of your dishwasher. It may or may not be covered. If it is covered, remove the lower dishrack, and then remove the cover. Your heating element is going to have two metal terminals. One at each end. Each terminal reaches downwards, into the base of the dishwasher. Mentally mark the area where each terminal enters the base of the tub. Now you need to gain access to the heating element's wiring. You can do this by first removing the lower kickplate panel of the dishwasher. There will be at least two screws (but maybe four) holding the kickplate panel in place. They are located either on the top or the bottom of the panel. If the screws are located on the top, you may need to open the dishwasher door in order to gain access to them. Close the door to remove the panel, though. Now look into the lower access area that you have just uncovered. Pinpoint the area where the heating element terminals extend through the base of the dishwasher. They will each have a wire connected to it. Label each of the wires so that you will be able to properly reconnect them later. Now you can pull the wires off the terminals. Each wire is connected to a terminal using a slip-on connector. Grasp the connector and pull on it firmly. DO NOT pull on the wire itself. Pull only from the connector. You may decide you need to use a pair of needle nosed pliers to help you. Use your multitester (aka multimeter) to test the heating element for continuity. Set the device to the ohms setting x 1. Touch each meter probe to a terminal. You should receive a reading somewhere in between infinity and zero. Because of the variety of makes and models of dishwashers, it is quite difficult to say exactly what the reading should be for each and every possible model. However, if the test you conduct produces a reading of infinite resistance (meter's needle does not move), then that is indicative of a faulty heating element, and you should replace the element. We hope this helps!
I need a new door for the soap dispenser. I couldn't find the item.
For model number WDF330PAHB4
Hi DeAna,
Thank you for your question. The door is only sold with the detergent dispenser. The part number listed under your model number for the detergent dispenser is PS11757054. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Hello Patrick, thank you for reaching out. The high-limit thermostat also known as the thermal fuse is located on the bottom of the dishwasher on the right-hand side of the washer next to the pump. We hope this information helps!
Was this helpful?
Thank you for voting!
Kim
December 30, 2023
I bought my dishwasher 6 months ago. Recently it is not washing the dishes. It fills and drains but does not wash. Is this a common issue? What should we do to fix it?
For model number WDF330PAHB4
Hello Kim, thank you for your inquiry. Based on our understanding of the issue, we would suggest checking the circulation pump, part number PS16744934, to solve the problem. We hope this helps!
Power is on no lights nothing will work tried reset but nothing happened. I was told it has control fuse but can’t find it
For model number WDF330PAHB4
Hi Richard, thank you for getting in touch. Based on our understanding, we would suggest checking the control board, part number PS12070630. It manages the functions of the dishwasher, such as washing, draining and drying. You may need to replace it to fix the issue. We hope this solves your problem!
I called an experienced plumber, who balanced and installed my new dishwasher properly, using the brackets I ordered from Parts Select, after an INEXPERIENCED plumber had tossed the factory-provided mounting brackets out with the shipping carton. Relief!
unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE.