Quick Question!

Have you ever purchased from PartSelect.com before?

Models > WDF310PLAW3

WDF310PLAW3 Whirlpool Dishwasher - Overview

Get Parts and Repair Help for WDF310PLAW3

If you know the dishwasher repair part you need, you can browse the list of all parts on the WDF310PLAW3, or you can search by name or part description. You can also find your part by where it is located on the WDF310PLAW3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for WDF310PLAW3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$38.65

Heating Element

This heating element is designed to monitor and control the heat of the water that enters the dishwasher. It is located at the bottom of the dishwasher. If your dishwasher is not d...

$6.12

Rack Track Stop

The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack stop may need to be replaced. The replacement part may differ slightly from the broken part, depending on the model. However, the different styles are interchangeable. This product is sold individually, and comes in both a white and grey plastic version. Many of our customers found this repair to be very easy. You will not require any tools to complete the job.

$11.43

Mounting Bracket

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher f...

$16.62

Upper Adjustable Rack Wheel - 2 Positions

Sold individually.

$4.89

Rubber Washer

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where...

$65.70

Drain Pump - 120V 60Hz

The pump ejects the water from the unit.

$18.32

High Limit Thermostat

This part acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this part will shut down power to the heating eleme

$4.40

Friction Sleeve

This part helps to keep your door quiet when it opens and closes.

$16.56

Retainer Clip - Black

This part is used to hold the access panel in place. Sold individually.

$3.02

Cover Screw

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dishwasher not draining after wash cycle

  • Customer: Andrew from Alexandria, VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 284 of 314 people found this instruction helpful
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.
... read more

Heater element broken.

  • Customer: Dennis from Sedro Woolley, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 124 of 132 people found this instruction helpful
Step 1: Remove the screws in the bottom of the countertop.

Step 2: Remove the screws holding the bottom kickplate.

Step 3: Loosen leveling legs.

Step 4: Pull dishwasher out of hole.

Step 5: Unlplug dishwasher.

Step 6: Disconnect wires from bottom of element in back.

Step 7: Remove plastic nuts... read more

Unit Wouldn't Work. "Clean" Light Blinking

  • Customer: PAUL from ESTES PARK, CO
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 67 of 94 people found this instruction helpful
The unit had power, but the controls would not work. The "clean" light was blinking. I first replaced the control unit, no help. I then used the "just ask" and was told the problem was the heating element and/or the hi-temp thermostat. I replaced both those and used the re-set code pushing the "hi-temp/air dry, hi-temp/air dry" buttons. That did it. Ea... read more