Models > WDB745REB0 > Instructions

WDB745REB0 Westinghouse Dishwasher - Instructions

All installation instructions for WDB745REB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WDB745REB0
301-315 of 452
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water discharge (around door) during Wash Cycle

  • Customer: Gary from Roseville CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After reading some "Suggested Installation Instructions" on the Parts Select Website, I felt at ease tackling this job. After opening the door, I simply pulled-out the existing door gasket. The installation involved simply pressing in the new gasket with my finger and insuring it was properly seated. The only tool I had to use was a pair of scissors to cut the excess length as I pressed it in. REALLY APPRECIATED THE SIMPLE INSTALLATION INSTRUCTIONS as I had never done this particular task.

water inlet valve was leaking

  • Customer: Jack from Wilton ME
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Could not identify the breaker for the dishwasher so I turned off the whole house. Turned off the water supply. Removed the leaking valve fairly easily - the clamp that holds it in place was a little tricky. New valve went on easily & again the clamp was a little harder. It was successful since there have not been any further leaks. Location of the valve & having to lie on floor to do repair was a factor in the ease of installation.

Tub Wheels were worn & broken

  • Customer: James from Hyde Park MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Got the parts in a DAY! Wheels were broken and worn causing top tray to slip off runners- new wheels were easy to put in-used the screwsfrom the old ones and banged out the job in about 20 minutes, including letting my son help. Thanks Partselect, you've hooked a new DIY'er (my son)

leaking all over the floor

  • Customer: Raymond from Harrah OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It was so easy that I could not imagine that it would work, but it did. Also, thank you for your great service. Finding the correct part on your site and quick delivery made the whole process very easy.

Leaking water under door

  • Customer: George from Angola NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Your video described the way to install the gasket perfectly.

Dishwasher leaks at the bottom front.

  • Customer: Jerry from Fremont NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I took a shot and ordered this $12.00 part plus shipping. The part looks better then the old part and it was easy to replace but it did not fix the leak. I think its a bad design because there is a gap in the middle of gasket where water can flow thru into this channel and then it overflows. So for now we just put a pan underneath to catch overflow because the rest of the dishwasher still works great.

standing water after done, poor rinse, dirty dishes.

  • Customer: Tucker from Woodward PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
unscrew top tabs of dw pull out,,unplug.. bail out water..disconnect drain and water at house connections..turn dw on it's side and unscrew old pump..ply off connectors..install new pump..bam!!

Dishwasher did not drain

  • Customer: Jason from North Little Rock AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I turned the power. Unhooked the dishwasher and flipped on the back exchanged drain pump. Perfect. Works like charm.

Lid on detergent dispenser wouldn't stay shut

  • Customer: Katherine from Fortville IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Found breaker switch for dishwisher and turned it off. Removed one screw on each side of bottom of door. Front panel slid off. Removed the two wires on dispenser, then took out the six screws. Pulled entire piece out from the inside of door. Put in new dispenser, attached wires (white on inside and red on outside). Put in the six screws and including the one with the little hook that holds the wires. Slid the front door panel back on and replaced the two screws (one on each side of bottom of inside door). Flipped the breaker switch back on. Approximately 25 minutes. Very easy, thanks to the person who wrote his/her instuctions previously.

The cap fell off and was melted on one side--therefore the rinse solution kept draining out.

  • Customer: Nancy from Williamsville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I was determined to find and replace the part myself. Much to my surprise, others had had the same problem! Thanks to the reviews on this website gave me the "courage" to do it myself!

My dishwasher was leaking from and electrical connection at the heating element

  • Customer: Kevin from Old Orchard Beach ME
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
There was an excellent "how to" video on the internet which also pointed me to the part I needed. I did not even remove the dishwasher as recommended. I removed the lower kick plate, removed the power connector at the leaking input, removed the bad nut and installed the new nut.

Brass Nut Cracked - Water Leaks O Floor

  • Customer: Robert from Oak Harbor WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I removed the 2 screws that hold the dishwasher in place. Slide out the unit just far enough to access the brass nuts on the heating element. Pulled off the wire, and replaced the broken nut with the new nut. Replaced the wire, slide the unit back into place and reattached the 2 under counter screws. Done!!!

Leaking water

  • Customer: Patrick from Knoxville IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced bottom gasket, still leaks. This was not the problem. Will have to keep looking for source of water leak. Bottom gasket installed really easy. Just pulled the old one out and inserted the new. Just was not the source of leak.

Spray arm melted to element!

  • Customer: Mary from St Marys GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
As a property manager in a small town it has been difficult to find adequate appliance repairmen. Being able to order the parts online and allowing any of my handymen install is a hugh relief. This has been a great ordering experience

Leaking at the door

  • Customer: John from Hammonton NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I just pulled the old one out and installed the new.
All Instructions for the WDB745REB0
301-315 of 452