Models > WDB11NRDS5 > Instructions

WDB11NRDS5 Westinghouse Dishwasher - Instructions

All installation instructions for WDB11NRDS5 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WDB11NRDS5
76-90 of 289
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Gasket leak

  • Customer: William from Sacramento CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
First I pulled out the old gasket and replaced with the new one. The new one is too long on purpose but only had to be trimmed a little for a perfect fit. Very easy and now no leaks.

My Dishwasher was leaking @ the valve on incoming line.

  • Customer: Jeff from Oxford AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 2 of 2 people found this instruction helpful
After i identified where it was leaking i cut the vave off under sink so i could remove part. All it had was 2 screws holding it to the frame and of course the copper line. I then went online to parts select and within 2 days my part arrived,i was planning on being down for at least a week but not with part select!! Thank you all for the great service!

The door springs were shot.

  • Customer: Scott from Oshkosh WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 2 of 2 people found this instruction helpful
Removed the bottom panel, and I had to disconnect the water supply, which did NOT use flexible tubing (much to my disappointment), removed the screws holding the diswasher in the cabinet. Slid it out, took the old springs off, put the new ones on.

It was pretty straightforward -- no big deal.

Intake valve was leaking

  • Customer: Lisa from Mastic Beach NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 2 of 2 people found this instruction helpful
removed two screws the disconnected the two hoses (after shutting the water off of course). It was easy.
Unfortunatley the water warped the wood under the vinyl flooring which is new and I really love. I would suggest that a rubber or some type of water proof material be placed under the dishwasher so that if it leaks it won't get at the subflooring. If this had been the case I would have noticed the leak right away.

The door springs were broken and the dorr was very heavy to open and close.

  • Customer: Yangde from Raritan NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
I removed the two screws and then moved the dishwasher out a little bit (about 6 inches). I pushed the dishwasher toward one side to make room for me to change the spring with my hand and repeated the same procedure for the other side. After the spring change, I turned an old dishwasher to a new one.

Broken wheel on upper rack.

  • Customer: Carol from Miami FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Replacement was simple.

spray arm came loose during cycle and melted onto the heating coil

  • Customer: matthew from Fayetteville NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Remove old spray arm and pressed the new part into place. Let the dishwasher run and the load came out very clean. Overall very pleased.

Dishwasher was leaking out of door seal. Sent PartSelect the brand and model number of the dishwasher and they did the rest. The replacement part was exactly the same as the old part. Delivery was fast and efficient. Only took a few minutes to replace and the dishwasher is back in running condition

  • Customer: Everett from Bridgeton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Pulled old gasket off with small hook. Replaced new gasket by pressing in with my fingers.

spray arm was knocked off and melted on the element

  • Customer: thomas from Jeffersonville VT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
I just popped on a new Arm. So easy. The amazing thing was how fast I had the part and how easy it was to find on Partselect.com. I ordered the part Monday and had it Tuesday. I was stunned and the tenant was impressed.

dishwasher leaked around the door

  • Customer: Karla from Hickory NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
First I pulled out the old gasket, used this to measure for the new gasket, cut to right length, pushed new gasket into the track and washed a load of dishes. No leaks! This took about 2 minutes to complete.

strike was broken

  • Customer: Ronald from Water Mill NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Easy as pie. I tokk the screws out that held the dishwasher to the counter top out. Then removed the screws holding the strike in place, inserted the new one, installed screws and then rescrewed the 2 screws backintothe countertop. Job done. All told 5 minutes.

Cap would not close

  • Customer: Felipe from Poughkeepsie NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
At first I wasn't sure; I thought I had to buy the inner panel of the door. Considering that I have to minimize expenses I made it a point to tackle the problem myself. I unscrewed the outter panel off the dishwasher door and located the dispenser from inside of the inner door panel.

I unplugged the old dispenser,which was damaged, unscrewed it from the panel and removed it. I cleaned any and all debris, dirt and soap scum it had accumilated over the short years we've owned it.

Finally; after I prepared the new dispenser for installation, I placed it in position screwed it in and plugged it in, which was slightly tricky because it is pretty snug against the inside door panel. Once installed, I got my older son, 15, to help me screw in the outside panel of the door, and as he held it I screwed it on the the inside panel.

I tested it with no dishes inside by pouring just a little detergent in the new dispenser, starting the dishwasher and I stuck around in case there were any leaks or any other possible disaster that could occur.

This was exactly one week ago and all is still well. By the way, the person who took my order, I believe her name was Joann, was great. She talked to me making certain I had the right part, which I was unsure of since the diagram on your site was not quite clear. On top of that; I didn't pay for overnight service, yet my part was at my door the next day. I was amazed at the quick service and delivery. Thanks Joann!!!

Felipe,
Poughkeepsie, NY

water leak

  • Customer: Jesus from Fort Madison IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 2 of 3 people found this instruction helpful
shut off water supply, unhook water line first so i could pull the washer out first. pull washer out and the valve is on the lower left if your facin the washer. easy to get to and very simple to change out.

Dishwasher would not drain

  • Customer: William from Bryan TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
replaced the motor after fixing the impeller once before. seems to be a weakness in this model based on what I've read here. The motor does not fail it's the little impeller inside the housing that comes apart. One word of advice: use a wet/dry shop vac to extract the standing water from the dishwasher.

Dish washer leaking at the door

  • Customer: Brian from Milford MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Pulled off the old gasket and replaced it the same way with the new one.
All Instructions for the WDB11NRDS5
76-90 of 289