Models > WDB11NRDS4 > Instructions

WDB11NRDS4 Westinghouse Dishwasher - Instructions

All installation instructions for WDB11NRDS4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WDB11NRDS4
211-225 of 325
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door strike broken

  • Customer: Janice from Conway NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed dishwasher from cabnet. Removed nuts holding old strike in place. Put new strike in place and then reattached bolts to hold strike down. Followed by reattaching dishwasher to cabnet. Ready to use

leaking aroung the door

  • Customer: cody from kalispell MT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced gasket easy-peesy

broken spring on door

  • Customer: Ralph from Berlin NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
replacing spring is easy.but you have to disconect the water line to slide the washer out to get at the spring.service was exelant. part was deliverd next day.

original rack wheels where bent and upper wheels had melted

  • Customer: Sharon from South Park PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
husband replaced wheels.

wheel missing

  • Customer: WILLIAM from KENNESAW GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
2 wheels were missing and I replaced them in 2 seconds. The diagram online was a huge help!

Had to replace the drain hose (that I screwed up)

  • Customer: Steven from Wauwatosa WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I already had the dishwasher removed for remodeling. I wrecked the drain hose myself. When I received the replacement it was a breeze to install.

Sprayer arm was falling over-so the dishes were not getting clean

  • Customer: Betty from Bloomfield NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just simply snapped the arm in place.

Dishwasher Leaked at the door

  • Customer: David from Middletown DE
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I replaced the bottom gasket first. It was kinda of tricky after pulling the old one out. The video on how to install it was very helpful and the installation took about a minute. The tub gasket was easy and fit right in. I just had to cut off the extra so it would fit in.

Dishwasher leaking arond the door.

  • Customer: David from Leesburg FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I checked with the possible causes and ordered the gasket suggested. I then clicked on how to replace the gasket and followed the directions given. Pretty simple.

Water discharge (around door) during Wash Cycle

  • Customer: Gary from Roseville CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After reading some "Suggested Installation Instructions" on the Parts Select Website, I felt at ease tackling this job. After opening the door, I simply pulled-out the existing door gasket. The installation involved simply pressing in the new gasket with my finger and insuring it was properly seated. The only tool I had to use was a pair of scissors to cut the excess length as I pressed it in. REALLY APPRECIATED THE SIMPLE INSTALLATION INSTRUCTIONS as I had never done this particular task.

water inlet valve was leaking

  • Customer: Jack from Wilton ME
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Could not identify the breaker for the dishwasher so I turned off the whole house. Turned off the water supply. Removed the leaking valve fairly easily - the clamp that holds it in place was a little tricky. New valve went on easily & again the clamp was a little harder. It was successful since there have not been any further leaks. Location of the valve & having to lie on floor to do repair was a factor in the ease of installation.

Tub Wheels were worn & broken

  • Customer: James from Hyde Park MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Got the parts in a DAY! Wheels were broken and worn causing top tray to slip off runners- new wheels were easy to put in-used the screwsfrom the old ones and banged out the job in about 20 minutes, including letting my son help. Thanks Partselect, you've hooked a new DIY'er (my son)

leaking all over the floor

  • Customer: Raymond from Harrah OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It was so easy that I could not imagine that it would work, but it did. Also, thank you for your great service. Finding the correct part on your site and quick delivery made the whole process very easy.

Leaking water under door

  • Customer: George from Angola NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Your video described the way to install the gasket perfectly.

Dishwasher leaks at the bottom front.

  • Customer: Jerry from Fremont NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I took a shot and ordered this $12.00 part plus shipping. The part looks better then the old part and it was easy to replace but it did not fix the leak. I think its a bad design because there is a gap in the middle of gasket where water can flow thru into this channel and then it overflows. So for now we just put a pan underneath to catch overflow because the rest of the dishwasher still works great.
All Instructions for the WDB11NRDS4
211-225 of 325