WDB11NRDS2 Westinghouse Dishwasher - Instructions

open dishwasher, pull out bottom rack, unscrew nut, install nut into sprayer arm, then with a clockwise motion screw sprayer arm with nut on to receiver until sprayer arm spins And nut is tightened. also i would like to thank PARTS SELECT FOR THE SPEEDY DELIVERY. THANK YOU

Turned off water & pulled plug from electrical outlet. Two screws removed the lower cover, two more screws hidden behind the opened door allowed the removal of the bottom panel. Laid a towel under the valve on the lower left to catch water & disconnected the inlet fitting with a 1/2" wrench. Remove the two screws holding water inlet valve next. With valve loose, remove electrical connector and drain hose (pliers). Valve has an elbow fitting that will need to be removed and installed on new valve - use Teflon tape or paste for a leak-free assembly. Reattach the drain hose & electrical connector before installing the valve using the two screws. Once in place, re-attach the inlet fitting (no Teflon required on tapered seats) and make sure everything is tight. Test washer through one cycle for water flow and no leaks. If all is good, remove towel and tools, then re-install the two lower panels. Clean up and you are done!

Removed kick plate at lower front of unit. At lower left is water inlet valve. Measured voltage across inlet valve solenoid at start of cycle. Was getting 120V to solenoid, but solenoid not opening valve thus no water going into dishwasher. Ordered replacement inlet valve. To remove inlet valve, disconnect two wires from valve assembly, disconnect water supply tube and remove two screws from mounting bracket. Now you can remove water hose that goes to dishwasher. Reverse order for install of new valve assy.

Took off all the screws, replaced the dispenser-no problem. However, I couldn't get the top to stay in place long enough to get the screws back in. My boyfriend came over and couldn't get it together without using a longer screw in the top area. Now it works great.
The only other problem was my bank and my VISA-they both called me stating my account was being used out of the country. They issued a fraud alert at first, but I called them and told them everything was fine.
Linda
Florida

The main tub gasket just pulled out by hand - no tools needed. Installing new one was just as easy, Just remember the wide part of the gasket sits in the bottom of the groove and cut off the excess with scissors.
Door gasket - not so easy. The six screws near the top of the door do NOT need to be removed, only the two (phillips) mid-way down the side. Remove the bottom panel by pulling down (it sits in a pocket of the top panel). The bottom door gasket just pulls out and insert the new one by hand (can be tight). Re-install bottom panel by sliding up into the top panel pocket, aligning the holes and screw home.
Normally,, you would be done but not in my case. The slow drip was still there. Investigation revealed that under the bottom panel (yes, we took it off again) is a tie-wrap holding wires at the bottom of the door that collects condensed steam and allows it to drip outside of the bottom plastic tray onto the floor. We thought that the tie-wrap was unnessesary and cut it off. Test drive- No more drips!

First I read the online bog's such as this one, those instruction said it was an easy task to pull out the old gasket from either side and then push in the new gasket in reverse of removal, in from either side, but the only way the gasket can be installed is to lay it along the channel it is to be installed in and then push it upwards. Due to all they butter and grease that gather's on the edges at the bottom of the door it is nearly impossible to slide it in place, so to push it up is the only way that will work!

First I unplugged the diswasher, than I unscrewed 4 screws on the inside of the door which pops the door off, unplug two wires, note which one goes where, unscrew 6 screws that holds dispenser in place, than reverse order to install new part. Very easy.

remove two small screws and slide the dishwasher out, lean it back and see where the water was leaking out. turn of the water remove water supply line and remove the water supply valve. then went to partselect.com and ordered new valve. the dishwasher is now like new for only $21.86 and UPS left the valve at my door in about 4 days::::LIFE IS GOOD

*Shut off power to dishwasher at circuit breaker (hot water supply had already been shut off under sink since inlet valve was broken and was allowing water to run into washer nonstop)

*Removed front lower panel from dishwasher

*Removed valve assembly from dishwasher frame

*Disconnected wiring harness from valve

*Disconnected incoming water line from valve

*Disconnected outgoing flexible water line from valve

*Installed new valve in reverse order

It was a pretty easy installation other than the small work area under the dishwasher.

I simply opened the door all the way and used pliers to grab hold of the old bottom gasket and slid it out sideways. Then inserted the new bottom gasket into the slot and pushed it in. No leaks for the new pergo floor. Half the battle was realizing that this thing was in there to begin with. It is a long thin plastic flap with a rubber strip on both sides not reallya gasket per say. Fast delivery and great instruction from other customers.

pulled out old seal replaced with new one very simple

Fisrt, I opened dishwasher door. I then pulled out the lower rack & put new part in place and pushed in lower rack. Last, I closed dishwasher door.

removed old gasket by hand, installed new gasket with hands only. p.s. great doing business with you,thanks.

Pulled out old part...slid in new...works great!

Shut off water, unpluggewd appliance, removed two screws holding part in place. Removed water supply hose from part to Washer, remover water supply from source to part. Reversed steps with new part. DONE! I'm not handy at all it was mostly luck diagnosing problem.