Models > WDB11NRDB1 > Instructions

WDB11NRDB1 Westinghouse Dishwasher - Instructions

All installation instructions for WDB11NRDB1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WDB11NRDB1
271-284 of 284
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dishwasher door was falling heavily down when pulled open because one of the two springs was broken

  • Customer: Mark from Apopka FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
identified the correct part to order. when it came, I used a Phillips-head screwdriver to undo the two brackets that hold the unit into the bottom of the countertop so I could slide it out a few inches. once I determined which spring was broken, I pulled out the remaining part and replaced it with the new one -- hooking it first into the hold farthest back in the appliance and looping the longer end over the top of the swiveling catch device that holds the front of the spring. then pushed unit back under countertop and screwed two brackets back into place with the existing wood screws and screwdriver. piece o' cake!

water leaking out the bottom of door.

  • Customer: Nancy from Turnersville NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the old gasket and slid in the new one. Very easy.

Inlet valve wasn't letting water in

  • Customer: Daniel from Lacona NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Turned off water and power! Couldn't move dishwasher out, so access was a little problem. Worked to disconnect inlet hose. Finally unscrewed the whole unit, disconnected the outlet hose and the power connection and then unscrewed the unit from the inlet hose. Removed the ell from old unit, applied Teflon tape, and screwed it into new unit. (Tighten it really well. I didn't and had to take things apart again!) Installed new unit starting with the inlet tube, then the outlet tube then the frame screws. Turned water and power back on and tested the dishwasher. SUCCESS! My wife thinks I'm a hero.

No water getting inside the dishwasher, making a loud squeeling noise.

  • Customer: Gayla from Shreveport LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
I'm a girl and it was pretty simple. I pulled out the dishwasher, removed the bottom plate cover. Removed the water line to the inlet valve and made sure the water was getting to the valve (it was). Removed the electical connector from the valve. Removed the valve and installed the new one. Made sure the water was pumping into the dishwaser. Pushed the dishwasher back into place. Runs great.

old lower spray arm falling off

  • Customer: David from Lakeland FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old arm and snapped New one on very simple

machine was not filling

  • Customer: jon from northampton MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First, I unplugged the dishwasher. After removing the under counter mounting screws, I pulled the dishwasher out from the cabinets. Because the switch is hard to reach, I put the dishwasher on its side (very carefully). Make sure to drain the dishwasher first, or it will leak all over your kitchen. To remove the switch, I unscrewed the single black screw in the middle of the switch and unplugged the electrical wires. I put the new switch in its place, screwed in the screw, and plugged in the electrical connection. I set the dishwasher upright, and ran it through a cycle before reinstalling it into the cabinet. I had previously tried replacing the water inlet valve, but that was not the problem.

The dishwasher leaked water at the bottom of the door.

  • Customer: Robb from Lehi UT
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The door gasket, part 154576501 did the trick. Your website was very helpful; it listed the percentage of times that the part resolved the problem. Very useful when you are guessing what the cause may be. It took me a little while to figure out how to put it in. It didn't seem like it set in place, but upon closer inspection I noticed a track to house the gasket. You don't have to take the door off, but doing so helped me to make sure the gasket was properly installed.

wetness under dishwasher door.

  • Customer: John from Bernardsville NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
saw the part i need. did a google, got you link, punched in my part, you guys made very easy to located the part. You even had a video which was helpful but yet not. I had to use more looking and figuring out but got it done.

Water leaking from the front, bottom left side.

  • Customer: Michael from Portsmouth NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Opened door fully, removed the tray. I was unable to remove the bottom gasket, or even see it at first. Many years of use actually made the gasket stick pretty firmly to where it was. Used my needle nose to pinch it and it came out very easy when I pulled. Cleaned the area ( and it needed it!) slid the new gasket in place without a problem. The Tub gasket came out without a hitch. Measured it to the new one and cut to length. Stuffed it in the crack and did some dishes. Small leak still in same spot. It's kinda of a funky fit in the corner so was a little more careful stuffing it in and it worked fine after that. Thanks...cheap, quick fix.

Top basket kept falling off the track

  • Customer: Daniel from Syracuse NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Removed the eight rollers that are screwed into the inside of the dishwasher upper section and simply screwed in the eight new ones. Only took about 15 minutes for the job.

Dishwasher didnt drain properly and the lower arm got stuck .The dishes did not come out vlean

  • Customer: Lois from Naples FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out the old one..snapped in the new one.Done

The close door code kept going off and was leaking on the bottom.

  • Customer: Roseana from Virginia Beach VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took the gasket off and put the new one on.

broken pump

  • Customer: EDGARDO from NEW YORK NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
By tilting the dishwasher over, I was able to remove the old drain pump and install the replacment pump. Only a small screwdriver was need.Took less than15 minutes.

door leak

  • Customer: Andrew from Republic PA
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled out old gasket and replaced with a new one.New gasket snapped right in place in bottom of door,
All Instructions for the WDB11NRDB1
271-284 of 284