Models > WCSR2090DGCC

WCSR2090DGCC General Electric Washer - Overview

Get Parts and Repair Help for WCSR2090DGCC

If you know the washer repair part you need, you can browse the list of all parts on the WCSR2090DGCC, or you can search by name or part description. You can also find your part by where it is located on the WCSR2090DGCC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for WCSR2090DGCC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.71

Tub Dampening Strap

Appliance would take 4 straps. It is recommended to replace all 4 at the same time. They keep the tub in the center of the cabinet. Sold individually.

$9.75

Drain Hose Extension - 4 1/2' Long

$3.27

Timer Knob Clip

$40.51

Dual Water Inlet Valve

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

$3.00

Drain Hose Clip

This clip holds the drain hose to the back of the washer.

$7.23

Tub Seal

The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably be installed by a qualified technician.

$11.54

6-Rib Drive Belt

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

$53.39

Drain Pump and Motor Assembly

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

$3.00

Tub Bearing

$6.62

Agitator Coupling

Bolt not included. This part connects the transmission drive shaft to the agitator base.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washing Machine was not draining water from tub.

  • Customer: Gerald from Midlothian VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 156 of 166 people found this instruction helpful
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)
2. Removed the... read more

washing machine would not go through all cycles or agitate

  • Customer: Brian from Millerplace NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 106 of 138 people found this instruction helpful
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok. read more

washer was overfilling

  • Customer: Matthew from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 92 of 106 people found this instruction helpful
Removed the water level pressure switch and the water inlet valve to test parts for proper operation with an ohm meter. Electrically, the switches seemed to work fine so I thought it was probably a mechanical water valve problem. I ordered and replaced both parts anyway just to be sure and potentially save time. read more