Models > WCRE6270H0CC

WCRE6270H0CC General Electric Washer - Overview

Get Parts and Repair Help for WCRE6270H0CC

If you know the washer repair part you need, you can browse the list of all parts on the WCRE6270H0CC, or you can search by name or part description. You can also find your part by where it is located on the WCRE6270H0CC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for WCRE6270H0CC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.71

Tub Dampening Strap

Appliance would take 4 straps. It is recommended to replace all 4 at the same time. They keep the tub in the center of the cabinet. Sold individually.

$9.75

Drain Hose Extension - 4 1/2' Long

$3.00

Drain Hose Clip

This clip holds the drain hose to the back of the washer.

$37.23

Dual Action Agitator

This does not come with the fabric dispenser - must order separately or use original part.

$7.23

Tub Seal

The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace ...

$11.54

6-Rib Drive Belt

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

$53.39

Drain Pump and Motor Assembly

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

$3.00

Tub Bearing

$6.62

Agitator Coupling

Bolt not included. This part connects the transmission drive shaft to the agitator base.

$7.45

Hub Nut

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washing Machine was not draining water from tub.

  • Customer: Gerald from Midlothian VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 156 of 166 people found this instruction helpful
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)
2. Removed the... read more

broken drive belt

  • Customer: jon from barry IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 43 of 51 people found this instruction helpful
To diagnose, first I unhooked the washer: power, water supply, and drain pipe. I then slid the washer out, laying it on its front. With nutdriver, I unscrewed two screws that held the other end of the drain tube and removed it completely. Then, again with the nutdriver removed 4 screws from the back near the legs, two in between the legs in the middle, and... read more

machine would not drain all other functions seemed o.k

  • Customer: douglas from danby VT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 36 of 36 people found this instruction helpful
Aside from getting the wet clothes and most of the water out,the toughest part of the job for me was to figure out how to get inside the machine. I nearly wrecked the thing trying to lift the top panel. After some frustration I removed the star-type screws on back of the control panel and found, tucked away neatly, the documentation/parts list complete with ... read more