WC504 Maytag Dishwasher - Instructions

Remove old seal by pulling out tabs one at a time.

To install new seal, I had to remove the front control panel and door panel to access the back side of all of the slots that the new seal tabs go into. Using needlenose pliers i pulled each tab individually until they were locked into place.
Replace door and control panel.

I ordered the part and it fit perfectly!! About five minutes to screw it onto my faucet and problem solved!!!

With the dishwasher door open remove the 3 srews connecting the top of the dishwasher to the bottom of the kitchen counter top. Remove the lower access panel from the dishwasher and lower the dishwasher about 1/4 inch in the front and back of the dishwasher). Once you have lowered the dishwasher enough slide the dishwasher out about 6 inches (enough to gain access to the door springs on the left and right side). Remove all broken spring parts and replace using new springs. The left side of the door contained a single heavy duty spring and the right side of the door contained a heavy duty and light duty 'helper' spring. I replaced only the right side springs since the left side spring was in excellent condition. When the springs are installed slide the dishwasher back into its original position and raise the dishwasher back up to its original height using the front and back adjustment screws. Replace the 3 screws holding the top of the dishwasher secure to the bottom of the countertop. Ensure that the door opens, closes and latches smoothly and then replace the lower access panel. Job done.

This repair is very simple. Partselect.com sells a repair kit for this problem that you can use but for simplicity the entire unit is not that much more. First remove the four outside lower philips head screws on the inside of your dishwasher door. Support outer door panel while removing screws. This will remove the outer door panel to gain access to the detergent cup. Remove panel by pulling out bottom first then slightly pulling downward. You will then see the detergent cup. Unplug the two leads that are connected to the unit keeping in mind their orientation. Remove the five screws that hold the detergent cup in place. Remove the cup assembly and gasket. Clean gasket area and install new cup and gasket. Reinstall five screws (do not overtighten) and plug leads back in. To reinstall door panel position door panel at a slight angle and install top first sliding upward into place under control panel then push inward at bottom. Reinstall the four philips head screws on the inside and you are finished. The complete repair will take you less than 30 minutes.

Removed the gasket by pulling it's tabs out of the metal slots in the door. This was accomplished by accessing the inside of the door.
Then I realized that I had to dissassemble the side and front panel of the door to install the new gasket. The reason is you have to pull the tabs through the metal slots in the door from the front side. I used needle nose pliers which worked well. Then I had to reassemble the front and sides of the door. No more leaks!! for now. Takes some time if you do it by yourself. Budget at least 2 hours.

the coupling for the water hookup for my rollaway dishwasher was very badly damaged. After looking everywhere including authorized dealer and repair places, on-line at the manufactures parts website, I finally broke down and ordered the entire hose assembly. When it arrived, I simply used a toothpick to carefully remove the new gasket from the new part and put in the the old one. It took about 30 seconds and works perfectly. I paid 60 bucks for a tiny little washer, but I have an extra hose assembly if something should go wrong in the future.

found detailed repair procedure at applianceaid.com which was relatively easy to follow - be aware that after years of service and some corrosion on the motor shaft it may be difficult or impossible to remove the plastic pump impeller and plastic drain impeller without damaging to get down to the shaft seal - the repair is not difficult for anyone with mechanical skills but I did have to order the two impellers and await their arrival before completing the repair.

Removed under-door front panel. Removed broken spring from right side. Hold door half open, insert spring with plastic bearing into hole in door hinge. Pull down to seat bearing in hinge. With needle nose pliers insert spring into hole at base of washer. ( You do not need to pull washer out of position)

remove lower access panel to expose spring. remove broken spring with longnose pliers. with door closed install upper hook of spring with nylon bushing on door hinge. using longnose pliers pull down on spring to hook on lower braket.

i took the dishwasher apart, took off the old hose and replace it with the new one. it was real easy. i smiled as my two yr. old tried to help me . i'm sure i'll be odering other parts in the future.

I had to replace the faucet in the kitchen sink orignnally. However since I use a porteable dishwasher, its hose connects to the kitchen faucet. The new faucets aerator is threaded differently than the old so that the dishwasher adapter would not screw in. I had misplaced the adappter kit that came with the dishwasher last year, so I ordered the adapter from partselect.com. when the part came a few day it was a simple as screw out the old aerator, screwing in the new adapted and then putting the modified aerator from the old faucet back in so that the dishwasher can be connected as needed.

First, I removed the 4 screws & Toe plate assembly below the door, exposing the undercarriage. The springs for both the right and left side are visible. Secondly, to help gain access to the springs (and for ease in reattaching the new sping to the appropriate tension bracket), I opened the dishwasher door and unscrewed the two small screws (located above the door) that secure the counter-top attach brackets to the underside of the counter. This would normally allow you the opportunity to simply pull the diswasher out a few inches from the counter for easy access. In my case, the lip of the counter did not allow me to pull the diswasher out very far, but I was able to angle it just enough to make access easier. Thirdly, I referred to the diagram that accompanied my replacement spring to make sure that I had the spring positioned properly. There appeared to be a slight difference between tension bracket spring angle for attaching the spring to the door vs side bracket. Fourth, I attached the vinly piece provided to the top spring connection and simply pulled down on the spring to create enough tension to attach the spring to the lower side bracket. Finally, test the door to make sure you have the proper resistance. Push the diswasher back into it's original position, realigning the top bracket holes and reattach the screws that secure the counter top attach brackets. Put away your tools, pack your patience and you are done. It's easy!

cleaned lime and calcium build up off of gasket
and it stopped the leak . yea . parts select was very helpful and said i could return the unused
gasket. . this is a good place to get parts.thanks larry

Removed the old gasket. It was easy to "pop out" the parts that held the gasket in place with a regular flat blade screwdriver. Becareful not to chip the porclien (sp). Any of the tabs that broke off I just pushed them through and can take them out if I ever need to remove the front of the door. Works fine and no leaks. Clean the area of the old gasket so the new gasket will have a good seal. End of story.

So I decided to stick in some CLR to see if it would clean it up. Well it got considerably worse. So ordered the new faucet adapter, threaded adapter and the two washers, due to not knowing what i would need. It came like unbelievably fast considering it was Christmas time. Unscrewed the old one from the faucet, screwed on the new one. hooked up the dishwasher, watched it for a bit for any leaks at the connection, and it worked great! I seem to have more water pressure too coming from the sink faucet. Thank you so much for the quickness in sending out my order! -- Scott