Models > WBVH6240F0GG

WBVH6240F0GG General Electric Washer - Overview

Get Parts and Repair Help for WBVH6240F0GG

If you know the washer repair part you need, you can browse the list of all parts on the WBVH6240F0GG, or you can search by name or part description. You can also find your part by where it is located on the WBVH6240F0GG by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for WBVH6240F0GG parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$132.82

Door Boot Seal

Also known as Bellow. The part may differ in appearance but functions same as original.

$152.41

Motor and Drain Pump

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This pump has sound isolation mounting washers and a filter.

$48.14

Drive Belt

The main drive belt is designed to work with the motor pulley and spin the drum until it comes up to speed.

$63.43

Drive Pulley Kit

This part is used to turn the drive belt with the help of the motor or transmission.

$55.30

Water Inlet Valve

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount o...

$35.89

Shock Absorber with Pin

This part helps stop your washer from shaking uncontrollably during a spin cycle. Sold individually.

$13.46

Water Inlet Pipe

$2.42

SCREW_ST4 20

$16.45

Suspension Spring

Sold individually. Appliance normally takes 2. The photo shown is incorrect.

$9.82

GASKET OUTSIDE CLAMP

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking from the door.

  • Customer: Brandon from Chugiak AK
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 108 of 120 people found this instruction helpful
I had to replace the door gasket because there was a small piece that had torn away, which caused large amounts of water to leak when the load of laundry was too big. Smaller loads of laundry would just produce a little bit of water.
Unsure of how to replace the gasket, I used a phillips screwdriver to pull the door and front panel off. I thought that ... read more

Rear Tub Pulley became loose and deformed pulley shaft

  • Customer: BRETT from CLINTON CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 78 of 92 people found this instruction helpful
Ordered new Parts. Removed old/worn parts. Found that the "hammering" from a loose pulley had worn and deformed the edges of the shaft where the flats are to accept new pulley.
Gently filed the flats with the flat surface of the file and filed the hump on the shaft that the "hammering" created. Take extreme caution to not file surfaces too much, becaus... read more

The rubber gasket on my front loader had a rip in it and soap and water would leak out at the bottom making a nice puddle to walk in on.

  • Customer: Gerard from Pompano Beach FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 60 of 64 people found this instruction helpful
I read and reread all of the installation repairs everyone had sent in. Everyone said on the average it would take 1-2 hours. I partly started the install myself and the ran into a problem. My wife was my helping second hands( second hands is a great help) and she suggested to either google or YouTube the repair. Within minutes I had found one on you tube a... read more