Models > WBVH5100H0WW

WBVH5100H0WW General Electric Washer - Overview

Get Parts and Repair Help for WBVH5100H0WW

If you know the washer repair part you need, you can browse the list of all parts on the WBVH5100H0WW, or you can search by name or part description. You can also find your part by where it is located on the WBVH5100H0WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for WBVH5100H0WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$132.82

Door Boot Seal

Also known as Bellow. The part may differ in appearance but functions same as original.

$152.41

Motor and Drain Pump

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This pump has sound isolation mounting washers and a filter.

$48.14

Drive Belt

The main drive belt is designed to work with the motor pulley and spin the drum until it comes up to speed.

$63.43

Drive Pulley Kit

This part is used to turn the drive belt with the help of the motor or transmission.

$35.89

Shock Absorber with Pin

This part helps stop your washer from shaking uncontrollably during a spin cycle. Sold individually.

$13.46

Water Inlet Pipe

$2.42

SCREW_ST4 20

$16.45

Suspension Spring

Sold individually. Appliance normally takes 2. The photo shown is incorrect.

$9.82

GASKET OUTSIDE CLAMP

$4.21

DISPENSER_SEAL

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking from the door.

  • Customer: Brandon from Chugiak AK
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 106 of 118 people found this instruction helpful
I had to replace the door gasket because there was a small piece that had torn away, which caused large amounts of water to leak when the load of laundry was too big. Smaller loads of laundry would just produce a little bit of water.
Unsure of how to replace the gasket, I used a phillips screwdriver to pull the door and front panel off. I thought that ... read more

Rear Tub Pulley became loose and deformed pulley shaft

  • Customer: BRETT from CLINTON CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 77 of 91 people found this instruction helpful
Ordered new Parts. Removed old/worn parts. Found that the "hammering" from a loose pulley had worn and deformed the edges of the shaft where the flats are to accept new pulley.
Gently filed the flats with the flat surface of the file and filed the hump on the shaft that the "hammering" created. Take extreme caution to not file surfaces too much, becaus... read more

Washing machine would cease functioning at the spin cycle and would not drain.

  • Customer: Trent from Shreveport LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 59 of 63 people found this instruction helpful
Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the front of the pump and... read more