W30400P Jenn-Air Wall Oven - Instructions

Open oven door, under the lip below the control panel there are 4 Phillips head screws and 4- 1/4" screws. If you have a screwdriver with interchangeable tips, you can use it for both fasteners. Remove the Phillips head screws first, Trim piece will drop down, clean while you have it out. Remove the 1/4" screws, the control panel will drop out about 4", it will be able to rotate towards you, you will see the display unit. Using a pointed knife, slightly pry the clip away and remove the two wired plugs. on the ribbon connector, on each side there are tabs, push these in and pull up not more than 1/8", the ribbon will pop out or take VERY little to remove, it is difficult, make sure the tabs on both sides are up. Remove the display via 1/4" screws. Reverse the process with the new unit but, make sure the tabs are up on the ribbon connector, this is the only thing I had problems with, took me about 3 min to figure it out. new display came with a "Static Electricity" warning. MAKE SURE YOU TOUCH THE FRAME OF THE OVEN BEFORE YOU TOUCH THE NEW DISPLAY UNIT TO AVOID STATIC DISCHARGE AND PROTECT YOUR NEW UNIT.

Watched the video and it was as easy as described. Not many things go as easily as this.

The repair went just as the directions that came with my order confirmation stated. It could not have been more straight forward. I love my new bright clock and panel display! Thank you PartSelect.

Replace the oven sensor per the excelent easy video you provided

Watching the video of how to replace the sensor was great help and much appreciated, the only difference was that my wires were much shorter and I had to pull the oven out of the cabinet to get to the back of the oven to release the clip holding the wires together, unlike the video where the man jiggled the wires until the clip holding the wires together came through the little slot where the probe is attached, otherwise it was pretty simple, just a few extra steps to pull the oven forward to get to the rear to release the clip holding the wires together. Once I was able to release the clip I used one of the 2 adapters that was sent with the sensor probe and attached them after putting the wires through the hole where the probe was attached first then replaced the 2 screws that holds the sensor in place, slid the oven back in and turned the circuit breaker back on and it works perfectly. The video gave me the confidence to do this job though and I thank PartSelect very much for being a great company to help with videos and sending the parts so quickly.

We took the back off the stove and unscrewed the two screws from the inside holding the sensor on and pulled it through and plugged it in and then replaced the screws. Very easy. We are still having trouble as the display does not read the same as the tempature is in the oven.

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks

Replaced oven gasket and both oven hinges. Repairs did not work. Oven door is actually worst. Do not waste your time replacing the oven hinges unless they are actually broken. When to Ace hardware and bought a package of 3 super magnets for about $10. Practice placing the magnets on metal strip on outside of the actual oven vs the oven door. This metal strip is not galvanized for which the oven cleaning latch goes through. Appeared to solve the problem. I then used epoxy glue to insure the super magnets would permanently stay in place. These are dangerous magnets that must be kept away from children and pets. You will spend more time separating these magnets from each other than gluing them in place. This part I will let you figure out but the only way to separate the 3 magnets from each other is the slide them, one at a time, from each other. Now I am awaiting 4 to 6 hours for the epoxy to cure. Best of luck. Jeff

Followed provided video

1. I removed the 4 Philip head screws that hold the trim plate on the bottom of the display panel and also removed the knobs from the display panel. 2. Then I removed the 4 hex screws from the bottom of the front panel 3. Remove the display panel and expose the Electronic clock. 4. Remove the two hex screws hold the clock. Moved the clock, then remove the three connections to the clock. 5 Attach the connections to the new clock and reassemble everything in reverse. Take about 20-30 minutes. Not a difficult job.

I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.

The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

Opened oven door. Inserted a small bent nail into the small holes on the hinge. This locks the hinge from closing all the way. Removed the chrome hinge retaining plates. One at each hinge. Lifted the door off the oven. Laid door on towel. Removed 3 screws from the top of door, three screws from the bottom of door. This allows you to separate the two pieces of the door. Clean all glass surfaces, including the ones under the middle glass panel. Removed 1 screw from each hinge at bottom of door. Pull hinge from bottom of door after removing screws. Insert new spring at top of door first, replace retaining screw. Realign the two door parts and replace all screws. Set door back on hinge pocket. Be careful to insure that the hinge seats into the pocket. Open door just enough to replace retaining plates. Process was easy, but it did not fix the problem completely. Bought heavy magnets from hardware store and installed them inside the door. This with the new hinge fixed the problem.

Loosen two screws to remove door. Removed outside trim and other outside screws hold center panel in place. Removed one screw holding hinge in place. Screwed new hinge in place. Re-attached center panel to outside trim and hung door. Easy enough.