Models > W25D6W > Instructions

W25D6W Admiral Washer - Instructions

All installation instructions for W25D6W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the W25D6W
1-10 of 10
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Intermittent problem with lid switch, no high speed spin/pump out

  • Customer: Linda from La Porte IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 16 of 21 people found this instruction helpful
Disconnect power, unsnap and raise machine top cover w/lid, remove old switch - two screws under lid, taking care to not drop loose actuator lever into machine. Remove control panel back and disconnect switch wire connector. Intall new switch, taking care to not drop loose actuator lever into machine, connect switch wires inside control panel. Replace panel cover and lower machine top cover w/lid and snap into place, reconnect power, verify operation...

Lid switch had deteriated over time and no longer made contact

  • Customer: James from Rochester NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
removed the screw holding the actuator, ordered the new part and replaced it when it arrived. Shipping was really fast and I even received it one day early.

Washer Spin Cycle Stopped

  • Customer: Diana from La Mirada CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.

lid switch acuator broke and some cycles would not work

  • Customer: Brian from Woodbury MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
unscrew the screw holding the broken part in the lid to remove the old part and tighten the screw to a firm position to hold the new piece in place. Now working fine.

Washer wouldn't spin because the switch on the lid broke

  • Customer: Rachelle from Eagle Mountain UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
I unscrewed the old lid switch and screwed on the new switch in seriously 2 minutes!

actuater broke and I replaced it in 5 minutes

  • Customer: Thomas from Clayton NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 10 people found this instruction helpful
unscrewed screw holding old actuater in and replaced it whith the new part.

a small plastic engage part was broke off that allows the washer to engage in each cycle

  • Customer: Teresa from Eminence KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
just a matter of 1 screw to remove and replace part ordered part 1 day and came in next day with regular mail. was a surprise for my daughter, she went on vacation and i fixed while she was gone. she was using different items to place in slot to engage each cycle.

Machine making grinding noise and vibrating excessively

  • Customer: John from Silverton CO
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Followed existing instruction to get tub and transmission out of the machine but we couldn't get the transmission free. Wound up taking the tub with the transmission attached to an appliance dealter who said we needed to remove the retaining clip on the bearing at the top of the transmission (inside the tub). We didn't have the tool to do that so we left it at the service center (60 miles from our location) and paid $291 for the repair then had to reassemble the unit when we got it home.

Lid switch actuator chipped off

  • Customer: Sandra from Killeen TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrewed one screw and replaced with new part.

Pad missing from both front legs which made washer dance around the room

  • Customer: Michael from DeSoto TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Easy as pie but had to cut one with hack saw to remove as it would not unscrew. Rust was the problem. Hack saw was the cure. Otherwise repair would have taken 5 minutes Washer now works as it did as a new appliance.
All Instructions for the W25D6W
1-10 of 10