Quick Question!

Have you ever purchased from PartSelect.com before?

Models > W256W Maytag

W256W Jenn-Air Wall Oven - Overview

Get Parts and Repair Help for W256W

If you know the wall oven repair part you need, you can browse the list of all parts on the W256W, or you can search by name or part description. You can also find your part by where it is located on the W256W by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. We’ve also included any installation videos we have for W256W parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

$29.46

Long Oven Sensor

This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.

$5.15

Screw

This screw is sold individually.

$5.15

Screw

Sold individually. Lock washers are used with screws when vibration from an appliance may cause the screw to loosen. Lock washers are also used in the electrical components of an appliance to ensure an electrical connection is not lost.

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$22.22

2 Piece Broiler Pan

The top of this part is now black.

$53.85

Bake Element (16" long x 17" wide)

This bake element is 17 inches wide. It has a terminal depth of three inches, and a total element length of ninteen inches. This element is intended for use with some electric oven

$9.73

Clock Knob - black

This clock knob is less than an inch long. It is all black in color and is made of plastic. This knob will accept a 'D' shaped shaft.

$66.07

Oven Door Seal

This oven door seal is twenty-one inches wide. This woven style door gasket is gray in color.

$8.65

Light Bulb Socket

This light bulb socket is located inside the oven cavity.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 107 of 124 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

F1-1 code

  • Customer: charles from marstons mills, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 46 of 57 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will ... read more

Repeated oven temperature sensor fault codes.

  • Customer: David from Arlington, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 23 of 26 people found this instruction helpful
First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the right side of the large ... read more