This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$11.73
In Stock
Order within the next 7 hrs and your part ships today!
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Order within the next 7 hrs and your part ships today!
Sold individually. Lock washers are used with screws when vibration from an appliance may cause the screw to loosen. Lock washers are also used in the electrical components of an appliance to ensure ...
$7.95
In Stock
Order within the next 7 hrs and your part ships today!
This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set ...
$37.51
In Stock
Order within the next 7 hrs and your part ships today!
This thermostat knob is two inches in diameter. It is a black knob with white numbering indicating the temperature inside the oven as well as the 'off' and 'clean' positions. There is also some chrome...
$45.58
In Stock
Order within the next 7 hrs and your part ships today!
This upper selector knob is two inches in diameter. It is primarily black with white lettering denoting the many different functions of the oven: bake, convection, broil, off, and clean. Its center is...
The oven seal replacement was very straight forward. Two screws held the door to the arms coming from the oven. I slid the door up off the arm and moved it to a workbench. This whole process should take about 15 minutes, a little longer if your unit is older and you want to clean as you go. Mine was fairly dirty and I gave it a cleani
... Read moreng as I removed parts. Unscrew all screws on the outer frame of the door, including two small ones on the side. Remove the outer frame and then the glass front and set them aside. A few more screws to remove the glass from the inner door, and even more on the remaining part of the door. You should also remove the screws holding the tiny brackets as well to release the portion that holds the oven seal in place. This is very straightforward, just keep pulling screws out until you can remove the old seal.
Once the old seal is out, insert the new one using the wire embedded in the seal as your guide...the gap in the seal goes to the bottom. Put everything back together and re-install the door. My door hinges were spring loaded and took a little effort to move them down so the door can be slipped on. This is a two person job since the hinges do not lock in place, they spring right back up flush with the oven and you cannot install the door. Re-install the two set screws holding the door to the hinges and you are done!
With the new seal in place, it felt a little puffy and the door did not seem to close as flush as it used to. This makes sense since the seal is new. I kept the door locked (like you would to use the oven cleaning cycle). I even kept it partially locked during cooking.
Frankly, the hardest part was the cleanup of nasty grease and dirt that built up over the past decade or so.
Unscrewed and pulled the door off and then took the three layers of the door apart in order to clean off the burned-on goop and remove the old and insert the new seal. The last screw was rusted in and the drill stripped it so that it was impossible to remove. I levered the remaining two layers apart, holding them open with screw drive
... Read morers, and inserted the new seal. Had to be careful with the shaping of the metal core of the seal and the distribution of the sealing fabric. Phew! I saved the screws from each layer separately by taping them to the counter in the order of removal. This made reassembly easier. Getting the door back on was a bit difficult and I needed another pair of hands to help me.
1.remove the trim around the door (8 screws) 2.remove over glass panel (part with the handle) Caution; the springs on the door are exactly set for the weight of the door. When we removed the outer glass panel, I almost killed my wife when the door slammed shut. 3.Remove inner metal cover (6-8 screws).some of these screws
... Read morewere baked pretty tight so I used vise grips on their little heads to convince them to get turning. 4. To get the door window out you must also remove the inner enamel baked cover, held on by 5-6 screws from the back. This is also the pieces which holds the door seal in place, so it is a good time to change that as well. 5. After cleaning up all the broken glass from the old window, the new window slides right in - perfect fit! Reverse the steps to put it all back together.
From the time the glass broke until it was completely repaired took only six days! Pretty amazing for a twenty year old oven.