Models > W20JA1

W20JA1 Magic Chef Washer - Overview

Get Parts and Repair Help for W20JA1

If you know the washer repair part you need, you can browse the list of all parts on the W20JA1, or you can search by name or part description. You can also find your part by where it is located on the W20JA1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for W20JA1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.68

Drive Belt

This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get we...

$4.05

Lid Hinge

This lid hinge in an inch and a half long and is used for some washing machines. It is all white in color and it is made entirely of plastic.

$4.75

Snubber Ring

$44.48

Drain Pump with Pulley

This pump has 2 ports. This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

$7.46

Lid Hinge Pin

$36.18

Transmission Pulley and Bearing Kit

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are not available separately - only available in this kit. A worn bearing causes slow or no spin.

$2.70

Screw

This screw is sold individually.

$2.70

Hose Clamp

$14.95

Tub to Pump Hose

$2.70

SCREW

This screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Load Grinding/Rubbing Noise in Rinse and Spin Cycles

  • Customer: Doug from Port Richey FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 111 of 122 people found this instruction helpful
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using a screwdriver to pry... read more

PUMP MAKING HORRIBLE NOISE AND BRAKE STUCK

  • Customer: MICHAEL from PLYMOUTH MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 58 of 66 people found this instruction helpful
The pump was very easy to replace (3) screws, easy to reach with front panel off. (less than 5 minut job. The brake assembly and thrust bearing was a little harder to do, but not bad at all. I found it best to flip the unit upside down to do the brake assembly. Replaced #10-24 x 1/2" screws with 2" long ones. Remember to do this (1) at a time, then back all ... read more

Hinge pin on one side and Lid hinge on the other

  • Customer: Jon from Ridgecrest CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 28 of 32 people found this instruction helpful
First I popped the lid up to about 70 degrees. Then removed the two hinges. Then removed and replaced the two hinge pins. The key is to then just start the two screws for the hinges, slip the pins in and then tighten the hinge screws. Total time was 5 minutes. read more