W205KV Magic Chef Washer - Instructions

Used piliers and screwdriver to remove old pulley.When putting on the belt make sure you have it tight enough.I had to buy a new pulley and do it over.

Removed the old hoses and screwed on the new hoses.

I tilted top cover to remove front washer panel removed suspension springs to remove complete tub assembly to gain access to bottom. Drive pulley to remove snubber ring I performed the repair step by step as per your video. was dead on made the repair go smoothly. I installed the belt last tilting washer mechine back to gain access to undercarrige just walked belt on all three pulleys self adjusting then. made sure washer was level. Front to back side to side no rocking in any deriction My wife did four full loads problems gone I think all needed to be done to complete repair snubber ring , washer drive belt, & leveling machine all played there roll in putting washer back in factory working condition washer not a angery walking vibration nightmare

Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.

I read some stuff on the internet where folks with the same problem replaced the water inlet valve to repair this same problem. So I did the same. However, after I installed the new water inlet valve, the problem was still there. It was at that point I decided not to guess at the what issue was and instead test the components in the washer. Yes, I am a lazy dumb ass. There are many of us out there. I decided to use a continuity tester to test all components in the hot water fill circuit and determined that the water temperature switch was bad. So I ordered a new switch from Parts Select (they rock - it showed up next day) replaced the water temperature control switch and...walla. fixed!!! Only took about 30 minutes to replace. Lesson learned: Don't be a dumb ass and guess. Test.

I'm a 69 year old female. My husband isn't very handy so I decided to order the parts and do it myself. I didn't know how to take the machine apart so I just moved the washer part so I could unscrew the screw. I dropped the screwdriver between the adj. and side of the washer. I guess you won't be telling this story. I did get the parts on and the lid is working and so is the machine. Valerie Guyot

Pulled up the top of the washer and removed the lid hinge with a star tip screw driver. Realized that I also needed the hinge pins and had to reorder those. They should come as a kit.

I obtained the parts on line and began to install these. I was surprised that the ease of my installation was great. Each part was held by one screw. I used a phillips driver and found the under screws easy to get to by pushing the inside clothes drum to the side. A total of four screws was required for the replacement. This repair was so easy that a normal non-trained person can accomplish it. Thanks Admiral.

I used two pry bars to evenly and gently remove old pulley then I gently hammered new one in place and reinstalled belt.

For this repair the tub must stay centered in the machine. I used a shim between the tub and front panel. Tilt the front of the washing maching aginst a wall and brace if needed. Remove the belt and pully. To remove the stator, I replaced 3 of the 6 bolts with a 2" long bolt of the same thread (replace every other bolt). This is needed because the spring is under 100# pressure. Remove the 3 original blots and than the 3 2" bolts. Remove each of these three a little at a time. Install the new stator and brake rotor. Use the 2" bolts in the stator to compress the spring. Reinstall the the other 3 bolts, pully, and belt.

1. Disconnected the electrical cord from the socket & the hose lines from the faucets.
2. Pulled out the washing machine from against the wall to make room for working.
3. Opened the back of the control cabinet by removing the 5 screws.
4. Disconnected the wiring ( making sure to identify all connections and color of wiring ) from the control cabinet and pulled through the opening on the cabinet top.
5. Popped the lid open from the front of the washer using a screwdriver by prying it open and removed the hinge lid from the cabinet top.
6. Removed the control cabinet from the cabinet top, disconnected the safety latch from the cabinet top.
7. Removed the water inlet guide & a vacuum hose from the cabinet top.
8. Removed the hinge brackets from the back of the washer which holds the cabinet top in place.
9. Removed the hinged lid from the cabinet top..
10. Installed new hinges on to hinge lid .

Installed new cabinet top in reverse order as above.

loved that I was able to get just the part i needed and not the whole shaft

Followed directions from video on your site. It was very helpful. The snubber ring fixed the problem.

We followed the instructions show on the video. However, our model was assembled slightly different. We had to remove the screws from both sides of the side panels so that we could remove the tub from inside of the machine. Also our model only has one belt not two.
Over all it was easy considering my husband and I had never attempted to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??

Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!

Hardest part was finding part that needed the needed repair. Searching the web for issues associated with the sound resulted in many links. Once the sound was found, I went to the video to see how to remove the Water Pump so I could examine it to confirm that was the correct piece. It took about 15 minutes to remove the part. Since I had to remove the belt to get it out, I realize that the belt needed replacement as well. So both parts were ordered. Replacing the parts also took about 15 minutes. Relatively easy repair. Be aware that the video on the part select video shows the water pump in a different location than the Maytag washer. To get to the Maytaq water pump, there is a panel in the back that had to be opened to access the water pump.