Models > W130W Maytag > Instructions

W130W Jenn-Air Oven - Instructions

All installation instructions for W130W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the W130W
16-30 of 45
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven light burnt out

  • Customer: William from Schwenksville PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 8 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Element burned out, broke circle, heat only half

  • Customer: Michael from Thornton TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.

The Broiler element split after oven self-cleaning

  • Customer: Rolland from New Port Richey FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
We at first thought the replacement could be done by just removing 2 screws.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.

replace element

  • Customer: alex from huntington NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.

Burnt out

  • Customer: David from Elba AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.

Broiler element broken

  • Customer: Walter J from Boynton Beach FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Very simple, unscrew the old element. Remove the electrical spade connectors and reverse to install new element. The folks at parts select.com were very helpful and even after I ordered the wrong part, the return process was hassle free. Prompt shipping, very happy.

knobs were worn out

  • Customer: Linda from Port Washington NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Just removed the knobs..they popped out easily...and replaced them with the new knobs

Thermostat bulb was hanging loose

  • Customer: Willi from Old Saybrook CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 2 of 5 people found this instruction helpful
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Replaced appliance bulb in owen

  • Customer: Billy from Grand Prairie TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed burnt bulb. On replacing the bulb I glued the bracket, retainer gasket and bulb cover together- I used only a small amount of glue-just enough to hold the three items together. You need to do this since the three items slip in your hand while you attempt to screw the bracket to the oven wall. Need my help, email me @ Lexidog999@tx.rr.com

element shorted out startedto arch inside oven

  • Customer: David from Traverse city MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
Turned off power, first then removed two screws
from bracket holding element. Then removed two
screws from element mounting bracket. I then
disconnected two wires using piers, and one with
a screwdriver. then put the newone in, in reverse.

couldn't read settings

  • Customer: Gladys from San Diego CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Removed all three knobs and replaced them with my new knobs, which are easily readable.

Selector Knob was lost.

  • Customer: Thomas from Lake Jackson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
The original kinobs were both black with white
markings. Come to find out that the selector
knob in black was no longer made. Had to replace
both knobs to match.

Bad broil grill

  • Customer: Aurelio from Lebanon NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Once oven was removed from wall not to bad

Had to replace heating element and element gasket

  • Customer: George from Camp Springs MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed old element and element gasket. Replaced both by alining gasket with element and screwing in retaining screws. Jod completed.

gasket was leaking heat from oven

  • Customer: NORMAN W from Waleska GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 5 people found this instruction helpful
removed old and installed new
All Instructions for the W130W
16-30 of 45