Models > VWSR4150DAWW > Instructions

VWSR4150DAWW Hotpoint Washer - Instructions

All installation instructions for VWSR4150DAWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the VWSR4150DAWW
76-90 of 488
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Wash basin wobbled excessively

  • Customer: David from Rochester Hills MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 5 people found this instruction helpful
Use paint scraper to release spring tabs holding front cover on.

Removed 2 screws holding lid down, and lifted up but did not remove top cover and control panel.

R/R 2 hex screws holding strap in place. If you are lucky and the broken strap is up front this is a super fast repair. Those of you with a rear strap will want to disconnect the wiring harness to the lid switch and likely remove the top panel (+ <5 mins).

Super easy and super cheap!

Tub made banging noise when stopping from spin cycle

  • Customer: Timothy from Broken Arrow OK
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 5 of 5 people found this instruction helpful
I notice a strange noise when ever the tub would shut down from a spin cycle. When I would load clothes it seemed that the basket had to much lateral movement. I looked between the top of the frame & basket & found 2 of the dampening straps had broken. Ordered 4 of them to replace all the straps.

Replacement was easy. I popped the front cover of the machine off. Remove 2 screws which held the top down which gave easy access to the straps. The straps are held in place by 2 screws so it was a simple process of removing the screws, removing the straps from their anchors & reinstalling the screws with the new straps. Job done. Reinstall the top & front of the machine & put the wife back to work.

Solinoid chattering when cold water was used

  • Customer: Dan from Marco Island FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
Removed 4 screwes on the top of the washer. Layed down the control panel and there was the inlets. Removed two screws and loosened the hose clamp. removed and installed new part.
It did the trick. No more problems.

Replaced drain pump on washer

  • Customer: John from Tompkinsville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 6 of 9 people found this instruction helpful
Took about 10 Minutes to have my washer up and running again. So easy, and I almost bought a new washer! Fixed it before my husband got home from work. Thank you PartSelect!

Water was leaking from machine.

  • Customer: RUPESH from BELLFLOWER CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 6 people found this instruction helpful
Open back cover and found that drain pump had a bad seal. Took it apart and bought new seal some what same size. Put everything togather and start washing clothers and wife complained that it became wost the before. When on line and found pump and price was just right to take a risk. Ordered on sunday and got ups tuesday.
Replaced pump on Sunday and leak was gone and wife was happy.

------Got chicken and beer that Sunday--------------

There was no fabric softener dispenser

  • Customer: Gigi from Monroeville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 9 people found this instruction helpful
The cap just removed by tapping a few times with a screw driver and hammer. then pulling upward it came off and I placed the new dispenser on. a couple minutes saved me from running up and down to add softener and it was very inexpensive.Thanks alot PARTS SELECT.

loud noise upon aggitation

  • Customer: Robert from Covington PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 6 people found this instruction helpful
replaced Tub dampeners Straps.

Timer knob had broken

  • Customer: Gary from New Albany IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 5 of 7 people found this instruction helpful
First off, the repair part arrived in only two days. The schematic was very detailed and accurate on your web site. Once the part arrived and removed from the bag, it was a snap to install with just a needle nosed pliers. Total time was less than 5 minutes. This was the first time I had used PartSelect and you can bet I'll be back. Thanks again. Gary K. in IN.

washer stopped spinning

  • Customer: Carl from Stone Mountain GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
I noticed the belt was off, first, then pulled it back on. Washer worked, but very noisily, as belt continued slippage. I bought new belt after reading how to repair, then when it arrived, I read how someone installed it without having to remove bolt, etc. I tried and succeeded. It agitates just fine, but stalls when spinning. It's like the belt is too tight, now. i am gonna try rotating the rotating parts to see if that will help loosen it.

Cold water would continue to flow even when it was supposed to stop.

  • Customer: Gregory from Campton KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 4 of 4 people found this instruction helpful
Removed knobs, removed cold and hot inlet hoses,removed top cover, removed output hose, wire plugs, and three screws and replaced the valve.

spin cycle slow, clothes too wet

  • Customer: Jeffrey from West Springfield MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 4 people found this instruction helpful
turned washer on side to get at the bolts holding motor. loosen bolts. remove flexable basket for water pump or one end of it. slide motor to loosen belt. remove and replace belt. use large screwdriver on motor to hold tension on belt while tightening nuts. hardest part was getting clamps back on the rubber basket.

washer barral spins with loud noise, turned out to be the worn Wahser Hub

  • Customer: shaobo from fremont CA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 6 of 10 people found this instruction helpful
1. take the machine apart, since the noise comes when the barrel is spining, I just watch for anything that contact to the axel.
2. without special tools, it was difficult to take off agigator, and a nut (that tighthened lefthanded).
3. Once defect part found, seach online for the part supply to replace.

replace coupling and agitator

  • Customer: Tricia from Glen Allen VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 10 people found this instruction helpful
unscrewed the old coupling, brushed off yucky build up and replaced, ta da back to washing clothes constantly !

Very noisy in spin mode

  • Customer: James from Colora MD
  • Difficulty: Really easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 5 of 8 people found this instruction helpful
a) remove front panel by depressing the 2 clips at the top in line with the lid b) remove the lid switch and 2 screws holding top on and remove top by tilting up SLIGHTLY and sliding to left. c) Remove agitator and by pulling straight up on it and remove adapter underneath d)remove 4 bolts holding 4 rubber straps to top of tub assembly, readily visible when top is removed. e) unplug motor wiring and disconnect pump and bleach hoses from tub f)while lifting up on tub, push down on each of the 4 suspension rods and disconnect them at bottom of tub ( this is the most difficult part, and to make it easier disconnect the rear rods first) g) tilt tub forward and remove tub assembly h) NOW, for the big nut that holds the spin basket in-- #1, it is LEFT HAND THREAD, so you will turn it to the right to remove it. #2, it is VERY TIGHT and requires a 1&11/16" spanner wrench (which I did not have) for removal. Instead, I used a 1&11/16 socket, an extension and an air impact wrench to remove and replace the nut. Assembly is reverse of removal and remember, that nut is ALUMINUM so be careful with that impact wrench when tightening it back up!I replaced the nut and split ring and cleaned the whole area thoroughly, and it greatly reduced the noise in spin mode. I did not replace the metal housing on the bottom of the spin basket, because it was $50 bucks. this probably would have eliminated all the noise, but my repair only cost $19 in parts, including shipping ,and the parts arrived in 1 day.

Water would not drain from tub.

  • Customer: James from Strafford NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 4 of 5 people found this instruction helpful
First I pulled off the front panel using a flat blade screwdriver to get it started. Then I could watch what happening as I tried starting the washer. When I put the dial to the Rinse Cycle and pulled the dial to start the washer, it would start to run for about 5 seconds and then stop. I tried this several times and the same thing happened. I noticed the water pump located in the front lower right hand corner was not running. It would only hum. I drained the tub by holding the wash machine drain hose into a bucket. If I held the hose down toward the floor, the water would flow freely out of the hose and into my bucket. As the bucket filled up I just raised the hose, emptied the bucket and repeated the process until the tub was empty. Sure saved time over trying to empty the tub by bailing the water out with a can. After the tub was drained I removed the two hoses from the pump and then the two mounting bolts and the pump was out. I bench checked the pump with an electric cord and it stilled just hummed. I knew for sure then the pump was bad.

I then ordered a new pump from PartsSelect.com. I entered my wash machine model number and PartsSelect gave me a picture of the replacement pump. I was a little worried that it did not look the same as my old pump but I ordered it any how. The night I got the pump I installed it in about 30 minutes. No problems, it just worked like a charm. Thank you PartsSelect.com I will definitely use you for all my appliance repairs in the future. I know there will be more.
All Instructions for the VWSR4150DAWW
76-90 of 488