VWSR3110W0AA Hotpoint Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The clothes have been dingy for quite some time.
I noticed the agitator would spin all the way around, in each direction. Also, the machine would make no sound, associated with washing, during that part of the cycle. I pulled the fabric softener reservoir off, with fingers on each side of the agitator, i pulled straight up and that gives you access to the coupling. Use a 7/16'" socket to loosen the nut, remove it and pull the coupling off. Press the new coupling on the splined shaft, tighten nut, and line up agitator with the grooves, push it down and replace fabric reservoir. Straightforward repair.
Parts Used:
-
Mark from Roanoke, VA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Water drip into washing well
Unplugged washer. Shutoff water supplies. Removed control panel. Disconnected wiring to valve. Removed hoses from old valve. Removed valve mounting screws (x2). Installed new valve and secured with mounting screws. Replaced washers in supply hoses and reconnected hoses. Reconnected control wires. Turned on water supplies. Plugged washer into electric outlet. Tested. EVERYTHING WORKING SO FAR!!!
Parts Used:
-
Scott from Jupiter, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Washer agitator wouldn't agitate
remove the agitator by just pulling it up, remove the bolt that hold the agitator coupling down and install the new one.
Parts Used:
-
Jose from Pulaski, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Agitator Would Not Move
Found that the teeth and the agitator coupler hade stripped out. Replaced the coupling and everything worked great. 10 Min and $10. 00 Fixed it up.
Parts Used:
-
TIMOTHY from KANSAS CITY, KS
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
agitator coupling broken
removed agitator unscrewed agitator coupling replaced with new one replaced agitator
Parts Used:
-
charles from WEST HEMPSTEAD, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
wouldnt agitate
Took off old agitator, removed coupling that was bad and put new one on.
Parts Used:
-
Shawna from LaCenter, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Agitator not working, spin cycle ok.
Removed agitator by pulling up, wiggle to and fro, watch out for unexpected release. Agitator coupler was worn, stripped splines. 7\16 socket, long extension to remove bolt in coupler. Install new coupler, new bolt, then line up agitator to splines on agitator coupler and push to snap in place.
Parts Used:
-
Walter from Atlanta, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Stripped plastic coupler spline
Remove agitator remove retainer screw and using Prybar lift off the old coupler ..... After removal use heat gun and wire brush to remove plastic residue from the splines of the motor shaft ... While the shaft is still warm line up the splines from the new coupler and using the mallet force the coupler on the shaft ... Install the retainer screw that comes with the coupler and snap on the agitator ... Done
Parts Used:
-
frank from palm city, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
The gear agitator had striped. Wouldn't spin the blades to wash the clothes.
I pulled up on the fin part of the agitator exposing the gear coupling. I unbolted the nut on top with a 12 mm socket. Once the nut and washer were removed I pulled up on the gear coupling and slid it right off. Reversed procedures to install the new one.
Parts Used:
-
Gerardo from Mountain House, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!