VVSR1070DCWW Hotpoint Washer - Instructions

Reviewed your website for problem symptoms for top loading washers not agitating and possible solutions. Purchased the lid switch wiring harness. All I needed was a painters 1" putty knife, wire cutters, Philips head screwdriver, (2) electrical connectors (crimping type), crimping tool, and electrical tape. Very easy installation and problem was solved. Recommendation, the wiring harness should come with electrical connectors (crimping type). The installation video on your website was a big plus in making this small project a success

First off, the repair part arrived in only two days. The schematic was very detailed and accurate on your web site. Once the part arrived and removed from the bag, it was a snap to install with just a needle nosed pliers. Total time was less than 5 minutes. This was the first time I had used PartSelect and you can bet I'll be back. Thanks again. Gary K. in IN.

It was almost a complete tear down. Most difficult part was discivering how to remove the front panel. Slip a putty knife between the top and front covers. push and depress the spring tab on each side. The left hand nut on the hub was difficult. I had to get a neighbor to hold a large pair of pliers while I put a pipe wrench on the nut and hit it with a 2 lb. hammer in order to break it loose. Puting it back together do not forget to reconnect the level sensing hose to the level selector, I did. Machine will not perform without it. You can do it! I did.

Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.

We pulled up diagrams online and read a lot about the repairs. Four screws on top took off the electrical panel. Two clips hidden under the front of the top panel released the front panel. We followed the clear tube up to the water level pressure switch. We disconnected the previous switch, and connected the new one, one wire at a time. We tested and found that the water now stopped filling. Put the washer back together - done! Cost - $30 and 1/2 a hour total vs. calling a repair person.

Just used hands to pry open the old agitator from the washer. If one angle does not work try another and go in a clockwise direction. The new agitator had a new coupling at the bottom, so I needed something to push it out from the top, found a long metal rod and easily pushed it down and out. Verified that new coupling was exactly the same as the old one. The old one was good so I just pushed the new agitator down on the old coupling and it worked fine.

First I pulled off the front panel using a flat blade screwdriver to get it started. Then I could watch what happening as I tried starting the washer. When I put the dial to the Rinse Cycle and pulled the dial to start the washer, it would start to run for about 5 seconds and then stop. I tried this several times and the same thing happened. I noticed the water pump located in the front lower right hand corner was not running. It would only hum. I drained the tub by holding the wash machine drain hose into a bucket. If I held the hose down toward the floor, the water would flow freely out of the hose and into my bucket. As the bucket filled up I just raised the hose, emptied the bucket and repeated the process until the tub was empty. Sure saved time over trying to empty the tub by bailing the water out with a can. After the tub was drained I removed the two hoses from the pump and then the two mounting bolts and the pump was out. I bench checked the pump with an electric cord and it stilled just hummed. I knew for sure then the pump was bad.

I then ordered a new pump from PartsSelect.com. I entered my wash machine model number and PartsSelect gave me a picture of the replacement pump. I was a little worried that it did not look the same as my old pump but I ordered it any how. The night I got the pump I installed it in about 30 minutes. No problems, it just worked like a charm. Thank you PartsSelect.com I will definitely use you for all my appliance repairs in the future. I know there will be more.

1) Unplug empty washing machine
2) Remove switch panel with star screw driver
3) Gently remove ground, two prong connector, and the water tubing from the water level pressure switch
4) From the front of the washing machine switch panel, pull water level switch knob straight off
5) Apply pressure to tin metal middle that holds the pressue switch in place so that the pressure switch can be rotated out of switch panel
6) Twist pressure switch off of the switch panel clockwise (from the front of the washing machine)
7) Set old pressure switch to the side
8) Place new pressure switch in tin groves and snap into place (the middle tap that you applied pressure to lock the pressure switch back into place)
9) Connect ground, two prong connector, and the water tubing to the pressure switch
10) Close washing machine panel and screw in all of the star screws
11) Push pressure switch knob back onto the pressure switch after aligning the hole to the rod

Open back cover and found that drain pump had a bad seal. Took it apart and bought new seal some what same size. Put everything togather and start washing clothers and wife complained that it became wost the before. When on line and found pump and price was just right to take a risk. Ordered on sunday and got ups tuesday.
Replaced pump on Sunday and leak was gone and wife was happy.

------Got chicken and beer that Sunday--------------

removed washer front panel, top panel to access the water fill spout and hose. Disconnected and replaced.
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.

turned off the water and removed the hoses. Then removed the screws that held the back plate (that contains the knobs). removed the two screws holding the water valves and the hose to the washer. replaced the valve and then reassembled the rest.

The hose has a tapered end that fits in a tapered hole in the back of the washing machine.When insalled the first time,the joint leaked badly.My solution was to coat the hose end and the interior of the hole in the back of the washing machine with silicon sealant;let it set up for a few minutes and install the new hose.This solved the leak and the hose seems to be working fine now.

Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry to wash :-)

Removed knobs, removed cold and hot inlet hoses,removed top cover, removed output hose, wire plugs, and three screws and replaced the valve.

the repair was really easy. All I did take down the control panel, disconnect the wires, pop out the switch, and blow through the air hose. I didn't realize what a simple machine it was.