Models > VVSR1040V3WW

VVSR1040V3WW Hotpoint Washer - Overview

Get Parts and Repair Help for VVSR1040V3WW

If you know the washer repair part you need, you can browse the list of all parts on the VVSR1040V3WW, or you can search by name or part description. You can also find your part by where it is located on the VVSR1040V3WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for VVSR1040V3WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.76

Tub Dampening Strap

Appliance would take 4 straps. It is recommended to replace all 4 at the same time. They keep the tub in the center of the cabinet. Sold individually.

$3.62

D-Shaped Knob Insert Clip

Sold individually.

$5.93

Agitator Coupling Kit

Washing machine agitator drive bell with bolt. It connects the transmission drive shaft to the agitator base. *NOTE: Hold down bolt not sold separately.

$3.27

Timer Knob Clip

$53.39

PUMP

$10.52

Drain Hose Extension - 4 1/2' Long

$44.73

Dual Water Inlet Valve

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount o...

$6.58

V-Style Drive Belt

$3.00

Drain Hose Clip

This clip holds the drain hose to the back of the washer.

$9.54

Tub Seal

This black new style tub seal is two and a half inches in diameter.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Agitator would not move during wash cycle

  • Customer: Mark from Lexington KY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 164 of 190 people found this instruction helpful
I placed both hands under the agitator 180 degrees apart, gave a quick jerk, and seperated the agitator from the coupling. With the agitator removed, use a socket and ratchet to remove the bolt holding the coupling to the spline. Remove the old coupling and slide the new one over the spline. Lightly tap on the coupling if necessary. Insert the bolt with ... read more

Washing Machine was not draining water from tub.

  • Customer: Gerald from Midlothian VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 138 of 147 people found this instruction helpful
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)
2. Removed the... read more

broken dampening strap and loose agitator

  • Customer: molly from laguna niguel CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 103 of 107 people found this instruction helpful
first remove the front washer cover by finding the two pressure clips that hold it to the top lid. gently push the putty knife into the clips one at a time. this will raise and separate them from the front panel. the panel will tilt forward and u can now remove it from the bottom clips by sliding it up and out. to open the top cover u remove the two 1/4 in s... read more