Models > VLSR1090G2WW > Instructions

VLSR1090G2WW Hotpoint Washer - Instructions

All installation instructions for VLSR1090G2WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the VLSR1090G2WW
31-45 of 313
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Changed drain hose on GE washing machine

  • Customer: Andres from Stamford CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
I attached the Drain Hose Clip to the Drain Hose Extension and then pushed the drain hose all the way into the drain hole in the back of the machine. I then screwed the clip to the machine. Done. Very painless. Fast delivery... ordered it on Monday, arrived on Tuesday.

Excessive agitator side movement

  • Customer: Richard from Spring City PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 11 of 14 people found this instruction helpful
Bought all of the parts to remedy this. It ended up being the top transmission seal/bearing which is not a replaceable part. I could see the shaft moving side to side. But the parts diagrams are not detailed enough to show that when assembled.

She led a good life.

My new side loader is SO MUCH BETTER AND INSANELY EFFICIENT. I highly recommend making the change if you need a transmission..

transmission leaking grease

  • Customer: Dennis from Chilhowie VA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set, Wrench set
  • 10 of 12 people found this instruction helpful
removed front cover the agitater then cover over large nut then large nut then inner tub then split ring and tub bearing then disconnected the hardware around the outer tub then replaced transmission then put back together in reverse order.

Hose and clip were broken in moving

  • Customer: DARYLD from SCHOFIELD WI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
The parts were here in 3 days and the repair went very quickly .Quality item would do business again.

Waher would not spin wet clothes.

  • Customer: Gerald L. from Las Cruces NM
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 10 of 12 people found this instruction helpful
Tipped washer over on to the front side. Removed back panel. Removed the flex coupling to the water pump. Removed the old belt. Installed the new belt and reversed the process to put components back together.

Noticed 3 straps were broken when we replaced the hose

  • Customer: Christine from Tempe AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 9 of 10 people found this instruction helpful
I removed the front cover, then unscrewed the top to expose the top. There are two screws that hold each strap, which turns out are different sizes, so I had to use two different sockets. I also had to remove the hose & plastic tube for the bleach. Once that was done, the replacement was easy, I replaced all 4 straps, reconnected the tube for the bleach, screwed the top back on and snapped the front cover into place. This took maybe 30 minutes - and I am female!

Washer was not filling up larger than medium

  • Customer: Joshua from Austin TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
Unplugged washer. Removed four screws on the top panel, unplugged and removed old water level pressure switch (which was visually broken), replaced with new part, put the top panel back on, re-connected power, and tested to make sure that the washer would now fill to Extra-Large. Worked!

Washer won't drain water

  • Customer: Ben from Lake Forest CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set, Wrench(Adjustable)
  • 9 of 11 people found this instruction helpful
Took front panel off the washer and found the pump working but no water drained from the tub. Took the motor off the washer by removing the two 10mm screws and attaching hoses. Decided to take the motor apart and found the propeller shaft has broken off inside the pump. Ordered new motor from Partselect and replaced it. Washer is working fine now.

Main seal leaking & burned bearings on & in transmission

  • Customer: Gregory from Mountain Home ID
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 20 of 44 people found this instruction helpful
Outrageous bad design for GE. We bought a SS tub washer but during repair found hidden aluminum components as 'wet' support structures, with massive corrosion; GE's SS tub is a fraud. Main seal went bad after 2 years, washer has a drip pan - no wonder, the problem was hiden for another year while parts burned up. Replacing transmission is basically simple if you have a large hammer and pipe wrench to remove the left hand turn aluminum main holding nut. Replacement parts were okay but we are going to sell washer & dryer immediately because of bad design - it will be a good machine for someone else for a couple years.

Purchased used washin machine w/o drain hose

  • Customer: Daniel from Oxford GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 8 of 8 people found this instruction helpful
After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.

Wasing machine strted to make horrible

  • Customer: Roman from Amherst MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 14 of 26 people found this instruction helpful
took it appart and found that the suspension rod was broken. went on line an ordered the parts.
The parts arrived 3 days later. Installed the parts and the washing machine was working within a half hour.

Washer over flowed radomly during wash or rinse.

  • Customer: RODERICK from BONITA SPRINGS FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 8 of 9 people found this instruction helpful
Two visits by GE Repair techs failed to clearly identify the problem.
After observing many fill ups, I decided the problem was an intermittant failure of the pressure fill switch.
GE wanted $80 for the service call plus $200 to replace switch, and recommended we buy a new Washer for about $400!
For $ 32 PartSelect shipped a new GE Pressure switch in about 3 days!

Openning up the top control panel required removing 4 sheet metal screws with 6 point star heads. The T-15/T-20 star driver was available at ACE hardware for under $2.
Removing the old pressure switch and installing the new switch was described in the GE Service Sheet that came with the washer (very easy).

I installed the part and solved the problem; the machine runs like new!

hub corroded away and left spin basket sitting on bottom of tub.

  • Customer: Leda from Port Saint Lucie FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 9 of 12 people found this instruction helpful
Biggest problem was getting old hub nut off. I had to remove it in pieces because it was corroded so bad.

Once hub nut was off it was a breeze to replace the parts after cleaning off the threads and shaft.

Reassembled in reverse order.. and ran.

I have to give accolades to PartSelect.. their customer service is second to none. i ordered the parts just before the Christmas holiday and they shipped them to my door in under 24 hours at no extra charge to see that I got them on time...
THANKS!.. It sure helped.

Would I do business here again.. YEP!

I will recommend you to others.

Thanks.

washer overflowed while running

  • Customer: Michael from Katy TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 8 of 10 people found this instruction helpful
First, I removed the four screws to expose the control panel. Then I removed both of the wiring connections on the switch, unscrewed the two screws holding the switch, and removed it carefully. Take the time to look at the old switch because it does not simply lift off the panel. It has a sliding lock to keep it in place on the panel and you must be careful when you remove it or install a replacement. The new switch installed easily, so I reconnected the power and started the washer. Bingo!

Water everywhere - overflowing washer

  • Customer: Sarah from Pylesville MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 13 people found this instruction helpful
We pulled up diagrams online and read a lot about the repairs. Four screws on top took off the electrical panel. Two clips hidden under the front of the top panel released the front panel. We followed the clear tube up to the water level pressure switch. We disconnected the previous switch, and connected the new one, one wire at a time. We tested and found that the water now stopped filling. Put the washer back together - done! Cost - $30 and 1/2 a hour total vs. calling a repair person.
All Instructions for the VLSR1090G2WW
31-45 of 313