VBXR1090D8WW Hotpoint Washer - Instructions

Removed the screws for the control panel and replaced the load switch and valve body in about 20 minutes. Simple fix and it's working perfectly!

replaced Tub dampeners Straps.

I had to remove top control panel and flip it over the back and out of the way, but did not have to unplug anything. I then had to remove front and top panels in order to remove the agitator and eventually the tub assembly itself. Once the tub assembly was removed, I had to turn it upside down to remove the transmissing and brake assembly as well as the mounting bracket. The entire removal process took about an hour and a half. The reassembly took less than an hour. The most difficult part was removing the 1 11/16 nut that ties the agitator to the tramsmission through the tub. It took 3 of us to hold the tub in place so that one of us could use the 3/4 drive ratchet and extension to loosen the nut. We did the same thing during the reassembly. All together there ware quite a few parts removed and a fair amounte of different screws. In order to perform this job, you must have a decent tool set and the ability to diagnose each step of the process, but it's not very difficult otherwise.

Removed front cover(use screwdriver)clips on top of cover under lid
Disconnected power from wall
Disconnected wires to motor 1 screw/unplug for motor
Uncwrewed clamp on drain hose
Removed top lifts off easliy
With help released Washing drum assy from hangers
Slid back and Tilted drum assy outwards from drum opening out to the front of machine
Pulled agatator up and off of hub
Remove one bolt from hub 1/4 " rachet w 3/8" socket
Pull off cap
Removed Locking nut(couterclockwise)nut is soft metal used good vice grips firmly locked on nut
Removed inner washing drum
Turned over Entire Assy (motor up)
Removed belt (slid off)
Removed 4 blots from Motor/Tranny assy to Plastic outer drum
Lifted off Motor/Tranny assy and pulled tranny out
Reaasemble in reverse order witht the exception of replacing the hub seal(inside)Outer drum assy.
There were service instruction under the front control panel.

First I removed the old part (2 screws)
Pulled off 4 wires (maybe the wrong word, I'm not a professional!
Put the new part in-turned the water on and had a stream of HOT water-yay
I had been putting this off because no one in my family had noticed (except me) and with my husband out of work it seemed like a low priority, but when my daughters came home for Christmas, they said "There's no hot water in the washing machine" so I took the plunge--I cannot believe I waited that long!
It literally took me seven minutes!

I remove three screws on top of the washer, moved the cover of the machine in order to get access to the water valve, and then desconnected the two solenoid of the valve,and removed two screws that hold the valve with the frame and installed the new valve in same order a took the old one.

I removed the front cover, then unscrewed the top to expose the top. There are two screws that hold each strap, which turns out are different sizes, so I had to use two different sockets. I also had to remove the hose & plastic tube for the bleach. Once that was done, the replacement was easy, I replaced all 4 straps, reconnected the tube for the bleach, screwed the top back on and snapped the front cover into place. This took maybe 30 minutes - and I am female!

Left up agitator, use socket set to remove agitator coupling. Then replace old agitator coupling with the new one. Tighten nut with socket set, replace agitator. Yes it is that easy.

Tipped washer over on to the front side. Removed back panel. Removed the flex coupling to the water pump. Removed the old belt. Installed the new belt and reversed the process to put components back together.

After realizing I had purchased a used washing machine without a drain hose I thought I would never find one, but then I found partselect.com. After easily locating the part on the web site from the detailed diagrams and model number I then ordered it. Receiving the part quickly I used a socket to remove the plastic connector that prevents the hose from disconnecting once the washer is turned on. I fed the hose through the plastic connector and into the drain hole without any issues. I then used my one small socket to secruely fasten it back together. There was no additional tools or items needed to successfully attach the washer drain hose.

removed the old one and replaced with new

On Friday the 13th, after spilling my coffee all over the table, I put the tablecloth in to wash. When I pulled the tablecloth out of the washer & put it into the dryer, I must have been angry at myself because I wrenched the dryer "Start" knob too hard & broke the knob off! I spent a few minutes looking for the part, and found that PartSelect had exactly what I needed at a very reasonable price. Once ordered, I received order confirmation, and, amazingly, the part arrived at my home in less than 24 hours after I broke the knob! Thanks, PartSelect!

Basically, I just followed the instructions in the video that is posted on this sight. It went off without a hitch. Removed the screws from the control panel, lifted it up and out of the way. Then I used the putty knife to release the clips that hold the front panel in place and then removed the top of the washer. Pretty easy from there to swap out the dampening straps and reassemble the washer. Saved a lot of money doing it myself.

Drain tub. remove 2 hose clamps and hoses. R&R 2 screws that hold pump.

It was very easy, just one screw to get the belt on, then it was just putting in place and putting it back together took the longest.