Models > VBXR1090B0WW > Instructions

VBXR1090B0WW Hotpoint Washer - Instructions

All installation instructions for VBXR1090B0WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the VBXR1090B0WW
61-75 of 478
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer overflowed while running

  • Customer: Michael from Katy TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 8 of 10 people found this instruction helpful
First, I removed the four screws to expose the control panel. Then I removed both of the wiring connections on the switch, unscrewed the two screws holding the switch, and removed it carefully. Take the time to look at the old switch because it does not simply lift off the panel. It has a sliding lock to keep it in place on the panel and you must be careful when you remove it or install a replacement. The new switch installed easily, so I reconnected the power and started the washer. Bingo!

transmission not working

  • Customer: Gene from Eddyville KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set, Wrench set
  • 10 of 16 people found this instruction helpful
Should be noted that the basket must be rotated on installation to find the best balance point!

Water everywhere - overflowing washer

  • Customer: Sarah from Pylesville MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 13 people found this instruction helpful
We pulled up diagrams online and read a lot about the repairs. Four screws on top took off the electrical panel. Two clips hidden under the front of the top panel released the front panel. We followed the clear tube up to the water level pressure switch. We disconnected the previous switch, and connected the new one, one wire at a time. We tested and found that the water now stopped filling. Put the washer back together - done! Cost - $30 and 1/2 a hour total vs. calling a repair person.

hub corroded away and left spin basket sitting on bottom of tub.

  • Customer: Leda from Port Saint Lucie FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 8 of 11 people found this instruction helpful
Biggest problem was getting old hub nut off. I had to remove it in pieces because it was corroded so bad.

Once hub nut was off it was a breeze to replace the parts after cleaning off the threads and shaft.

Reassembled in reverse order.. and ran.

I have to give accolades to PartSelect.. their customer service is second to none. i ordered the parts just before the Christmas holiday and they shipped them to my door in under 24 hours at no extra charge to see that I got them on time...
THANKS!.. It sure helped.

Would I do business here again.. YEP!

I will recommend you to others.

Thanks.

Broken knob

  • Customer: Laura from Woodbridge VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 8 people found this instruction helpful
On Friday the 13th, after spilling my coffee all over the table, I put the tablecloth in to wash. When I pulled the tablecloth out of the washer & put it into the dryer, I must have been angry at myself because I wrenched the dryer "Start" knob too hard & broke the knob off! I spent a few minutes looking for the part, and found that PartSelect had exactly what I needed at a very reasonable price. Once ordered, I received order confirmation, and, amazingly, the part arrived at my home in less than 24 hours after I broke the knob! Thanks, PartSelect!

My washer was overfilling

  • Customer: Torrance from Southfield MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
the repair was really easy. All I did take down the control panel, disconnect the wires, pop out the switch, and blow through the air hose. I didn't realize what a simple machine it was.

My washer would not drain the water out.

  • Customer: jayme from drummonds TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 6 of 7 people found this instruction helpful
IT was so easy to replace the pump. I think the hardest part was trying to get the pliers to work right. All I had to do was unscrew two bolts, take off two pipes, get the new pump and replace the pipes and bolts. It was that easy.

Water Overflow

  • Customer: Shelby from Binghamton NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 10 people found this instruction helpful
1) Unplug empty washing machine
2) Remove switch panel with star screw driver
3) Gently remove ground, two prong connector, and the water tubing from the water level pressure switch
4) From the front of the washing machine switch panel, pull water level switch knob straight off
5) Apply pressure to tin metal middle that holds the pressue switch in place so that the pressure switch can be rotated out of switch panel
6) Twist pressure switch off of the switch panel clockwise (from the front of the washing machine)
7) Set old pressure switch to the side
8) Place new pressure switch in tin groves and snap into place (the middle tap that you applied pressure to lock the pressure switch back into place)
9) Connect ground, two prong connector, and the water tubing to the pressure switch
10) Close washing machine panel and screw in all of the star screws
11) Push pressure switch knob back onto the pressure switch after aligning the hole to the rod

tub fell down on one side

  • Customer: douglas from Stockton CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 10 people found this instruction helpful
after ordering part and getting the wrong part sent to me i was able to finally get right part to my house 2 weeks later, i pulled front cover off with a screwdriver took out broke rod and inserted new part closed cover and hooked power back on and was in business

the bottem of the tub

  • Customer: michael from warwick RI
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set, Wrench(Adjustable)
  • 6 of 7 people found this instruction helpful
at the bottom of the tub their is a mettal peace witch holds the tub to the transmision witch is made of zink(aka junk metal or zink+tin)witch broke stoping tub from sping the clotes dry so atfer odering the new part and nut..
and finding out that it is a LEFTHAND nut made of alumanum
taking a small drill bit 1/8" and drilling the nut to weakin it making it brake able then cleaning the treds up
the new part fit right in the tufest part was hold the trans still to get the nut on tightenuf to hold the tub

Water leaking through Tub Seal

  • Customer: Roger from Port Saint Lucie FL
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 7 of 10 people found this instruction helpful
First and foremost, the job would have taken 2 hrs instead of 8 hrs. The problem was that no one on the help instructions said that the Hub Nut had a LEFT HAND thread and suggested to just break the nut off. Well, after chiseling off most of the nut I drilled small holes through the nut and removed the nut pieces. However; I learned that I had damaged the transmission seal and had to buy a new transmission $183. Had I known this the job would have taken much less time and at a cost of about $50.
PS: The washer runs great.

Washing Machine would not balance on spin cycle

  • Customer: Jarid from Louisville KY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 19 people found this instruction helpful
I replaced the work tub dampening strap because that what everyone recommended to replace for this problem. However the purpose of these straps is to dampen the agitation cycle and they have nothing to with the spin cycle at all. the balance ring assembly had been rubbing on the outer tub so I decided to replace it because of a "balance issue". However the ring is liquid with baffles to counter balance the load as it spins and it still had the liquid inside of it so it was actual not needed. What fixed my issue was I found a bolt laying at the bottom of the washer. This bolt was one of the 4 bolts that hold the outer tub to the metal support. When it feel out the tub was only held in at 3 points not the needed 4. This allowed it to rock a bit in the high speed spin and you thought it was going to fly into a 1000 pieces. I replaced the bolt and other parts since I had paid for them and everything works great now.

washer loss balance

  • Customer: james from sidney OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 7 of 11 people found this instruction helpful
went very well thank you

Washer would not spin

  • Customer: Rick from Ephrata PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 8 people found this instruction helpful
Removed the front panel with a stiff putty knife, removed the worn belt. Placed the new belt on the front pully and than the rear pully, turning clockwise. After checking the spin cycle I put the front panel back on and I was done.

Water would not shut off when filling

  • Customer: Robert from Fairview Heights IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 11 people found this instruction helpful
I removed four hex screws from the top of the washer. I found the water level pressure switch and removed the dial. I turned it to remove it from the holding bracket. I removed both wires one at a time and placed them in the new switch one at a time so I wouldn't get them mixed up. I put the new switch in place and put the top back on using the hex screws. The dial was replaced. When I tested the dial I found that the dial did not match up to the water settings. They didn't even come close. Although the numbers were close on the switches, they were different. I had to remove the new switch and put the old one back on until I can locate the correct switch for my washer.
All Instructions for the VBXR1090B0WW
61-75 of 478