VBXR1060TAAB Hotpoint Washer - Instructions

I went to your web suite to get part numbers. Found your videos. It told me what my problem was and how to fix it. Pull clip off. install new knob reinstall clip done. Very easy and fast. I couldn't even get a repairman out that fast.

The hose has a tapered end that fits in a tapered hole in the back of the washing machine.When insalled the first time,the joint leaked badly.My solution was to coat the hose end and the interior of the hole in the back of the washing machine with silicon sealant;let it set up for a few minutes and install the new hose.This solved the leak and the hose seems to be working fine now.

1) Unplug empty washing machine
2) Remove switch panel with star screw driver
3) Gently remove ground, two prong connector, and the water tubing from the water level pressure switch
4) From the front of the washing machine switch panel, pull water level switch knob straight off
5) Apply pressure to tin metal middle that holds the pressue switch in place so that the pressure switch can be rotated out of switch panel
6) Twist pressure switch off of the switch panel clockwise (from the front of the washing machine)
7) Set old pressure switch to the side
8) Place new pressure switch in tin groves and snap into place (the middle tap that you applied pressure to lock the pressure switch back into place)
9) Connect ground, two prong connector, and the water tubing to the pressure switch
10) Close washing machine panel and screw in all of the star screws
11) Push pressure switch knob back onto the pressure switch after aligning the hole to the rod

First I pulled off the front panel using a flat blade screwdriver to get it started. Then I could watch what happening as I tried starting the washer. When I put the dial to the Rinse Cycle and pulled the dial to start the washer, it would start to run for about 5 seconds and then stop. I tried this several times and the same thing happened. I noticed the water pump located in the front lower right hand corner was not running. It would only hum. I drained the tub by holding the wash machine drain hose into a bucket. If I held the hose down toward the floor, the water would flow freely out of the hose and into my bucket. As the bucket filled up I just raised the hose, emptied the bucket and repeated the process until the tub was empty. Sure saved time over trying to empty the tub by bailing the water out with a can. After the tub was drained I removed the two hoses from the pump and then the two mounting bolts and the pump was out. I bench checked the pump with an electric cord and it stilled just hummed. I knew for sure then the pump was bad.

I then ordered a new pump from PartsSelect.com. I entered my wash machine model number and PartsSelect gave me a picture of the replacement pump. I was a little worried that it did not look the same as my old pump but I ordered it any how. The night I got the pump I installed it in about 30 minutes. No problems, it just worked like a charm. Thank you PartsSelect.com I will definitely use you for all my appliance repairs in the future. I know there will be more.

removed washer front panel, top panel to access the water fill spout and hose. Disconnected and replaced.
personnel at part select were very knowledgable about detailed part and the overnight service was right on time.
I would recommend part select for your next appliance parts needs.

turned off the water and removed the hoses. Then removed the screws that held the back plate (that contains the knobs). removed the two screws holding the water valves and the hose to the washer. replaced the valve and then reassembled the rest.

Removed knobs, removed cold and hot inlet hoses,removed top cover, removed output hose, wire plugs, and three screws and replaced the valve.

the repair was really easy. All I did take down the control panel, disconnect the wires, pop out the switch, and blow through the air hose. I didn't realize what a simple machine it was.

It was real easy......
1. removed the 4 phillips head screws from the top of the control panel. The control panel is hinged and pulls forward towards you
2. Holding the Control Panel Chassis at an angle look between the knob and the backing ring for a clear c clip. (Note: you are looking for the open end not the closed end of the clip) Take a small flat blade screwdriver, place it between the timer knob and backing and press down until the clip slides off the spindle.
3. Remove the knob.
4. Before removing the wiring on the timer assy unplug the power cord from the wall socket.
5. Locate the green grounding wire on the timer assy and remove it with pliers.
6. Remove the main control connector by squeezing the tabs.
7. There was only 1 hexhead screw holding my assy to the chassis, remove and carefully pull up the left side of the assy just enough for the timer spindle to exit the chassis.

At this point its just the reverse order to connect the new assy.

turned washer on side to get at the bolts holding motor. loosen bolts. remove flexable basket for water pump or one end of it. slide motor to loosen belt. remove and replace belt. use large screwdriver on motor to hold tension on belt while tightening nuts. hardest part was getting clamps back on the rubber basket.

Took front of washer off,found that all of the straps were broke ,removed two small bolts from each strap pulled plastic support from from broken strap and put it in new strap,put plastic supported end of strap in first put bolt in and mounted other end to drum,easy job just about any one with common since could do it.Got to go laundry to wash :-)

I noticed the belt was off, first, then pulled it back on. Washer worked, but very noisily, as belt continued slippage. I bought new belt after reading how to repair, then when it arrived, I read how someone installed it without having to remove bolt, etc. I tried and succeeded. It agitates just fine, but stalls when spinning. It's like the belt is too tight, now. i am gonna try rotating the rotating parts to see if that will help loosen it.

Originally my water level sensor was broken. When I was repairing that, I noticed that the dampening straps were broken. Replacing them was easy. The hardest part was remembering how to open the top. I just searched the internet until I found the answer. I can't remember it all right now, but the key was to slide a putty knife in between the top and the front to pop open the body.

Took about 10 Minutes to have my washer up and running again. So easy, and I almost bought a new washer! Fixed it before my husband got home from work. Thank you PartSelect!

The hardest part of this repair was actually getting the panel off to get at the timer itself. You need a special type of screwdriver with a torc head, (not sure about spelling) ( looks like a phillips head but has an extra "prong") . After that it was as easy as unplugging the old one and plugging in the new one. piece of cake.