Models > UKI1000AXX

UKI1000AXX Maytag Ice Maker - Overview

Get Parts and Repair Help for UKI1000AXX

If you know the ice maker repair part you need, you can browse the list of all parts on the UKI1000AXX, or you can search by name or part description. You can also find your part by where it is located on the UKI1000AXX by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. We’ve also included any installation videos we have for UKI1000AXX parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Exact Part matches for your search term [Viewing 1 of 1]

$107.68

Add-On Ice Maker Kit

This part number matches the current model number "UKI1000AXX".

This kit is used with some top-mount refrigerators from 1997 to present. It includes the icemaker, bucket, water valve and other necessary parts for installation.

Sections of the UKI1000AXX [Viewing 1 of 1]

$109.45

Replacement Ice Maker

NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.

$2.70

Screw

Sold individually.

$2.70

Screw

This screw is sold individually.

$14.89

Water Fill Cup and Bearing

$36.78

Single Outlet Water Valve

This valve has a 1/4" tubing inlet connection. When energized, this part releases water from the supply line into the ice mold.

$24.48

Thermostat with Clips

This part is also known as the cycling thermostat and this bi-metal device controls the activation of the icemaker ejection cycle.

$3.96

Compression Nut

$3.56

Plastic Tubing

1/4" Plastic tubing, 8 1/2 feet long.

$2.70

Screw

This screw is sold individually.

$3.84

SCREW

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 509 of 520 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 205 of 276 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.

  • Customer: David from Chester CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 62 of 75 people found this instruction helpful
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover whic... read more