Models > TWX233RBD3 > Instructions

TWX233RBD3 Tappan Washer - Instructions

All installation instructions for TWX233RBD3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TWX233RBD3
16-30 of 136
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No Cold Water

  • Customer: Mark from Pittsburgh, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 13 people found this instruction helpful
Checked problem on-line and discovered it was the water inlet valve. Matched the part on part select. Com. Finding the part was very easy. Part select had a grid behind the picture to help determine the size and pictures from all sides. Removing the old part, matching it, and replacement took a total of 30 minutes. I now have clean clothes.

Washer machine would fill up with water and not spin and drain

  • Customer: MARC from MANALAPAN, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 15 of 22 people found this instruction helpful
Happened to slam the lid by mistake and the washer started spinning. Recognized the lid lock was working haphazzardly. Also, there was a burning type odor coming from the switch. So I lifted the lid top and disconnected the switch from the lid by unscrewing 2 screws and 4 wires. When I received the new switch, I reinstalled it with 2 screws and reconnected the 4 wires.

washer belt broke

  • Customer: Carl from Boxford, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 11 people found this instruction helpful
followed the instructions on a blog

Pump leaked

  • Customer: Robert from Roswell, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 10 of 11 people found this instruction helpful
First I turned off the water. Since the pump is at the front of the machine,it was easy to get too. I then removed the hoses by squeezing the hose clamps with pliers. I removed the electrical plug and then removed the 3 screws holding the pump to the base. I changed orientation of the outlets per instructions,which was very easy. Installation of the new pump was performed in reverse. I had difficulty getting one of the hose clamps back on and changed it to a screw clamp. I turned the water on,ran the machine and checked for leaks. Partselect saved me several hundred dollars in repair costs.

Washer wouldn't spin

  • Customer: KELLEY from KANSAS CITY, MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 14 of 24 people found this instruction helpful
Received lid lock within 24 hours, fixed washer within 10 minutes...up and running. Thanks.

Stopped agitating versus level washer feet/leg

  • Customer: Sandra from Denton, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 12 people found this instruction helpful
My washing machine stopped agitating and spinning and I couldn't afford a repair man...plus I wanted to exhaust any obvious problems first. One of the leveler feet had broken years ago. Since I luckily had determined via reading other posts that the agitator won't work if the cycle safety switch is not functioning right, I thought the safety switch might need to be changed but after careful thought, I decided to order a new levelling leg first because maybe the broken levelling leg was shaking the safety switch so it wasn't connecting right. Once I received the leg overnight, I flipped the washer on its side and had to drill out the old leg. It was a little tricky because of how it broke, but the drill worked. I flipped the washer back up, leveled it with the new foot, and the agitator was miraculously working again...just like new. I didn't need the safety switch. Thanks to partselect.com for having the details of my washer parts to study up on and get me the right part so quickly. I saved myself alot of money.

Tub was leeking

  • Customer: Gregory from Fort Worth, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 12 of 19 people found this instruction helpful
Lifted top
removed adgetator
removed tub top
removed inside tub
removed inside tub holder bracket
repaced seal
replaced,replaced.....

No hot Water to washing machine

  • Customer: Dominick from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 9 of 10 people found this instruction helpful
S/O Water , Removed front panel, removed screws from side panel water valve accessible. Removed screws that hold water valve, installed new valve reassembled washing machine.

no draing water

  • Customer: VICTOR from THORNTON, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 11 people found this instruction helpful
just change the new pump conected to trhee wires and two pipes.

No Final Spin Burning Smell

  • Customer: NELSON from MAYWOOD, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 8 of 9 people found this instruction helpful
Removed 2 screws at bottom of the front panel - removed front panel by sliding the panel down about 1/2 inch and then away from the appliance- v belt is removed by pushing the tensioner pulley to remove tension from the belt and turning the pulley untill the belt is removed instalation is a simple reverse of the process. I did't have a repair manual so every step was trial and error untill I was able to complete the repair.

washer went into spin mode but would not spin

  • Customer: Damon from Hinesville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
I removed the front panel to see the belt was snapped in two. The front roller is sping loaded, so I gave it a little tention, slid the belt back on and viola! it was that easy. If your washer starts to vibrate more and sounds louder than normal, get a belt as soon as possible because that may be the problem. Once I put on the new belt, the machine ran as quiet as it did when I first bought it.

crack in drain hose

  • Customer: mary from port jefferson station, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 11 people found this instruction helpful
First I went on-line and found a download for the parts catalogue which contains a schematic for the washer. After looking this over I could determine how to get the washer apart! After getting the front panel off, I disconnected the drain hose from the pump with a pair of water-pump pliers. As I pulled this hose out, water spilled out all over the floor, so I then cleaned that up. Next I connected the new hose and put the machine back together. This job would have cost me over $150 if I had called in a repairman. PartSelect saved me so much money, and I thank them so much!

Leaking water from machine

  • Customer: Martinus from Fort Lauderdale, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 9 of 17 people found this instruction helpful
This repair is realy very easy
As discribed by the others

Burning smell, lots of hi-pitched squeaking

  • Customer: Heather from Stephenville, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
I got online and figured out exactly how to take off the front of the washer and then how to replace the belt. It was so easy. The part itself arrived much sooner than predicted. It fit perfectly and my washing machine is now running smoothly and quietly.

Wash tub would not drain/burning rubber smell

  • Customer: Clay from Kansas City, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
I removed the top of the washer by removing two screws on the back. I located and bypassed the lid switch to make sure that wasn't the problem. The problem still existed so I removed the two screws that hold the front panel of the washer. Using a flashlight, I located the drive belt and immediately saw that it was out of position and had pieces missing. I cut and removed the old belt, placed the new belt on the tub pulley and slowly maneuvered it onto the motor drive wheel. I then squeezed the tensioner pulley so that the belt was seated. I turned the timer dial which started the washer and it immediately began pumping the water out of the tub. Problem solved!
All Instructions for the TWX233RBD3
16-30 of 136