Models > TU8000XLP0 > Instructions

TU8000XLP0 Whirlpool Trash Compactor - Instructions

All installation instructions for TU8000XLP0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the trash compactor repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TU8000XLP0
31-45 of 82
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Wouldn't come back up after compacting

  • Customer: mark from st george, UT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 2 of 4 people found this instruction helpful
replaced switch and fixed the problem. Still had one more problem after that though, but got that figured out and fixed that to.

Grinding sound when operating compactor

  • Customer: Don from Los Angeles, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Removed drawer first, then removed compactor from under kitchen cabinet. Removed top cover. Discovered that a small wash cloth was wound around one of the drive screws. I then removed plunger and put it back in position. Replaced top cover and turned on compactor. Plunger went to the top and made a grinding sound. I removed the cover to discover that when I put the plunger back in, I did not have the lever that trips a micro switch in proper position. I needed the replacement plastic gears that were ruined when compactor did not shut off. Relatively easy job if I had noticed the location of the shut off lever, and would have needed the parts.

ram wouldn't go up or down.

  • Customer: Mona from San Diego, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 2 of 4 people found this instruction helpful
pulled it out, turned it upside down, and removed the gear, then replaced it, turned it back up and pushed it back it worked.

Compactor stop working

  • Customer: Jackie from Malone, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
I flipped this unit over,removed 4 screws to the drive gear.I tore apart found a nut came off the screw rod.Which broke the drive gear.I looked on line found the parts select page.That showed the diagram i needed,to order parts, i needed.The wife and i tackled this task,of repairing this product.The repair was quick and easy.It took less than 30 minutes including cleanup.The wife happy,that all that matters.
Jack

compactor wouldn't shut off

  • Customer: Ray from Dallas, GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
changed out the switch and that fixed the problem

Toe guard was broken, foot pedal was discolored.

  • Customer: Michael from Ashfield, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 5 people found this instruction helpful
Replaced both, results like new.

motor gear broken

  • Customer: Clem from Scottsdale, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
There were no instructions that came with the parts kit other than how to set the spacing for the gear lash. There were parts in the kit which I have no idea what they are (4 inch long plastic pipes?. Having 4 years experience with Sunbeam appliance repair was an asset. The old melted and broken gear came off easily with a few strikes of a hammer on a flat blade screwdriver. The replacement gear was a perfect match and the scroll pin was put in with a little gusto effort (tight fit as it should be). It would be great if just one gear or the other could be ordered....

Pushed button, made a buzzing noise, nothing happened.

  • Customer: Adrien from East Freetown, MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 2 of 5 people found this instruction helpful
Laid compactor over on its side. REMOVED 5 SCREWS holding cover plate to expose gear drive. Found that large drive broke in half. Used screwdriver to start split ring then pliers to pull it off the rest of the way.Take off the washer . Next I needed to losten the 4 nuts holding the drive motor. This allowed me to slip the rest of the drive gear off the drive shaft. It was then a simple matter to put the new gear back on the chain then slide the whole thing back on the drive shaft. Replace the washer then slip the split ring back in place and seat it home with the pliers. Retighten 4 nuts on motor support. Put cover back on with 5 screws 2 in front 3 in back Pushed button it worked.I must mention that this was a Sears compactor but when I went to their online parts they no longer supported it. I found Part select and they suggested I look at a Kitchenaid compactor and after checking out the picture it looked the same,Iordered the part and it was the same. Thanks I guess I'll come to you first now.

Trash Compactor didn't work

  • Customer: john from salinas, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set
  • 1 of 2 people found this instruction helpful
The plastic power nut had stripped out on my 12 year old trash compactor. Ordered 2 new ones from Partselect and installed them. Now it works like new again.

Door would not open.

  • Customer: Stephen from Midland, TX
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
Took of top housing; saw traveling compactor not properlly alligned. Removed cover from Power Nut; saw that it was stripped. Ordered new power nut. Replaced power nut & aligned traveling compactor. Replaced top housing.

Compactor would not open. Ram was down

  • Customer: James from Flagstaff, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 1 of 2 people found this instruction helpful
Once I discovered that the ram was down, I had to determine why. Opened up the bottom and discoverer the drive gear was broken. Ordered the parts kit and made the repair. Did not know what the other parts in the kit were for, but it works.

Plastic Gear Wheel Broke

  • Customer: Reagan from Glenshaw, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 1 of 3 people found this instruction helpful
Emptied all garbage! Laid machine on its side. Removed cover. Removed left over gear parts by removing pin. Loosened chain by removing two top left corner screws. Place new plastic gear in position with chain. Returned screws to top left corners. Returned pin to gears. Make sure chain is taught. Replace cover. Lift back up from its side. Test.

worn guard scratched door panel

  • Customer: harold from walpole, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 3 people found this instruction helpful
removed old parts and replaced

Broken Drive Gear

  • Customer: Michael from Painted Post, NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 4 people found this instruction helpful
Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.

Ram quit moving

  • Customer: Hal from Granada Hills, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Removed bottom and replaced gears
All Instructions for the TU8000XLP0
31-45 of 82