Models > TRT18NREW0 > Instructions

TRT18NREW0 Tappan Refrigerator - Instructions

All installation instructions for TRT18NREW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TRT18NREW0
196-210 of 221
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door handle broke off

  • Customer: Robynn from Essex Junction VT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Cleaned the surfaces,installed the new handle...WaLa! Could not have been easier. Plus the new handle arrived in 2-3 days. AND was less than 1/2 the price of ordering through Sears Parts. I would use PartsSelect again in a heartbeat! Thank you for your great customer service.

FREEZER WORKED FINE, REFRIGERATOR WAS 47 DEGREES

  • Customer: Allan E from Manhattan IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I WENT ON PARTSELECT PUT IN MAKE AND MODEL NUMBER, A LIST SHOWED THE PROBABLE CAUSE. I WATCHED THE HOW TO VIDEO. WHEN I RECEIVED THE PART IN SHORT ORDER I LOOSENED 2 SCREWS DISCONNECTED THE WIRING PLUG (SPRAYED IT WITH CONTACT CLEANER) PLUGED IT IN, REMOVED SCREWS FROM OLD PART PUT THEM IN NEW ONE. PUT TIMER BACK IN ITS LOCATION AND TIGHTENED THE SCREWS. VERY EAZY, WORKS FINE.

MY FRIG LIGHT STOPPED

  • Customer: Susan from Rapid City SD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I AM A 65 YEAR OLD WOMAN WITH NO MECHANICAL APTITUDE: I just unplugged the frig. and used a screw driver to pry of the plastic socket from its outside edge..Then you just unplug two tiny contact plugs that appear when you pull out the socket and replug in those two the same way on the new part. Pop the socket back into the hole ....and screw in the new bulb. I knew I needed the socket part cause when the bulb burned out , a new bulb still did not work...If I can do it, anyone can!

Overheat coils at the bottom inside of the freezer

  • Customer: Costas from new hyde park NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I pick up very fast at these kind of small jobs but because of my very busy schedule I decided to call (2 times) technicians about my problem but none of them had any idea. About my repair, I removed the grill at the bottom of the refrigerator, unscrew a small plate (located on the bottom left side) that's holding the defrost timer. I plug on the new part, screw back the plate with the defrost timer and that was it. Don't forget to turn clockwise with your finger the timer until you hear a "click" and then turn it slightly more to the right. There is also a video on U-tube.

the evaporator fan same time won't stater

  • Customer: Armando from Eagle pass TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
change the evaporator fan motor kit working perfect

door handle broken

  • Customer: nelson from ville Platte LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Unscrew the attached broken piece from the refrigerator (two screws). line up the new door handle with the existing screw holes and attach. Simple.

Broken Glass Shelf

  • Customer: Annie from West Plam Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
1) Remove glass from shipping Container. 2) Using fingers, place glass ever so gingerly in the shelf tray. 3) Pour a glass of wine to celebrate.

changed defrost timer

  • Customer: Gerry from Apache Jct AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed the video very esay

fridge side was getting warm.

  • Customer: Darryl from Russellville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
open freezer door two screws just below unscrew slide piece to side unplug reinstall very simple.

Replace evaporator fan motor.

  • Customer: Joseph from New Ringgold PA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Replace evap fan motor. Take a close-up picture of the evaporator fan motor installation prior to removing. Take pictures as removing various components.

Refrigerator section warm, freezer working properly

  • Customer: Kenneth from Collegeville PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the advice of many people with the same problem, and replaced the Defrost Thermostat and Defrost Timer. Both repairs were relatively easy, and the problem appears to be solved. The replacement of the Defrost Timer is very easy (about 30 minutes), and I wish I had stopped at that step and waited 48 hours to see if that fixed the problem. But, I wanted to replace both parts that I had purchased - - In my refrigerator, access to the Defrost Thermostat is through the back of the freezer panel. Not too difficult to get to the area, but I had a bit of a problem in replacing the part, and might have been better-off to see if step 1 fixed the issue. The problem that I ran into is that I don't have a crimping tool, and crushed both of the connecting sleeves when trying to 'crimp' them with a set of wire-strippers. Rather than to invest in a crimping tool, I connected the wires and sealed with electrical tape - - Now that the issue is resolved, I will likely re-open and use a proper connecting sleeve (with a proper crimping tool). My advice is to buy both parts, and replace just the Defrost Timer first. Chances are good that it may fix your problem, and you are only out $20 for the second part, which you can leave in your junk drawer until you may need it some day! All in all, it was a great way to spend $40 and avoid a costly service call!

No problems at all.

  • Customer: Anthony from Albuquerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very EASY!! just unpack, wash, and place into slots above crisper doors. A child could do this.

refer quit cooling and so did freezer

  • Customer: jerry from petaluma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!

Freezer wouldn't go in to defrost cycle

  • Customer: John from Long Beach CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After some troubleshooting to ensure the thermostat and heating element were working, determined that the defrost timer was the problem. With the defective part, I was able to manually advance the timer to activate the defrost cycle, but it wouldn't do so on its own. Unplugged the refrigerator from the wall. Timer is located in the refrigerator compartment at the very top. The compartment houses the cooling thermostat, the light bulb and the defrost timer. Using 1/4" nut driver, remove 4 screws holding compartment cover to top of fridge. Lower a bit to access electrical wiring. Wiring harness can be unplugged to work on the timer away from the fridge which makes it a bit easier. Timer is mounted with 2 phillips head screws. Remove screws and unplug timer from wiring. Install new timer, plug in wiring, secure with the phillips head screws and remount entire compartment.

Faulty defrost timer. Freezer would not maintain temperature

  • Customer: Steve from Nineveh IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watched the video once. Removed four 1/4 inch screws with a nut driver unplugged the unit, took out two screws securing the timer. Replaced did all of this in about 10 minutes. It was "exactly" as the video showed and it's worked perfectly since the replacement of the faulty timer. I saved a $75.00 service call minimum and the part was more than likely cheaper from Part Select than from the repair facility. Although I'm a pretty good handy man, you would not need any experience to make this repair. The instructions are precise and the part fit perfectly.
All Instructions for the TRT18NREW0
196-210 of 221