Models > TRT18GRED0 > Instructions

TRT18GRED0 Tappan Refrigerator - Instructions

All installation instructions for TRT18GRED0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TRT18GRED0
76-90 of 177
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.

  • Customer: Larry from Newton KS
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 4 people found this instruction helpful
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

Freezer okay, but fridge was warm

  • Customer: brad from minneapolis MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Website was great!

The defrost timer was right in front. 2 minutes and a screwdriver and I had it replaced.

To replace the thermostat, I had to take out the back panel, defrost it and then install the new part. the only problem was that the heatshrink tubing they sent was too large. Otherwise, it worked great.

Evaporator in freezer freezing up, fridge warm

  • Customer: DONALD from MECHANICSVILLE MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
REMOVED SHELF BRACKETS TO ALLOW THE REMOVAL OF THE EVAPORATOR SHEETMETAL COVER.UNPLUGED WIRES TO THERMOSTAT ,REMOVED DEFROST TIMER AND PLUGGED IN NEW TIMER,(FRONT LEFT LOWER KICK PANEL).CUT AND RESOLDERED WIRES TO NEW THERMOSTAT REINSTALLED THERMOSTAT AND COVER IN REVERSE ORDER.

I KNEW WHAT PARTS I NEEDED AND HOW TO REPAIR THE UNIT,HOWEVER YOUR CUSTOMER COMMENTS WERE SPOT ON AND WOULD HELP ANYONE PERFORM A SUCCESSFUL REPAIR (YOU PROVIDE A HELPFUL SERVICE FOR THE PUBLIC)

Refrigerator was not cooling and the motor was running constantly

  • Customer: Anil from Somerset NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 1 people found this instruction helpful
Having tried PartSelect.com before, I was very comfortable with the process. Input my symptoms and the feed back I received was that one of the 2 things (Defrost Timer or Defrost Thermostat)might need replacement. Since the cost was not much and over night shipping would cost more than the product, I decided to order both the parts. Changing parts was a breeze. The instructions posted by others on your web site were very easy to follow. You guys save me a bundle every time I have any thing going worng with any of my appliances.

sheft ends brolen

  • Customer: Helen from Gulf Breeze FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Cleaned and removed old ends, applied new ends and installed. Ends fit to order, shipping quick and parts affordable. Thank you

door end cap broken,

  • Customer: Edward from Piscataway NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Put the new ordered door end caps in place, everything worked fine.

Refrigerator keeps frosting up and not cooling

  • Customer: Marvin from Pima AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Refrigerator started frosting up and running all the time.I'd defrost it and it would frost up again in about a week.The timer seems to be work so I just guest it mite be the Defrost Thermostat.I removed the duck in the center and back panel in the freezer compartment defrosted it and switched Thermostats and replaced panel and duck, going to lower compartment of the refrigerator.So far it seems to be working a little more time while tell.

clips on both end caps we broken and the crossbar kept falling off.

  • Customer: Frank from Orange Park FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
First i pulled the crossbar off the door, then I pulled both end caps off the crossbar and then I
put the two new end cap on the crossbar and then tapped snoggly into place with the palm of my hand. Job done. took all of about 5 seconds.

No freezing or cold in either freezer or refridgerator - compressor did not run.

  • Customer: George from Sunnyvale CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

freezer worked frig was warm. Ice maker is still not working

  • Customer: steve from Kirkland WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall

broken shelf bar with missing end brackets.

  • Customer: Robert from Oconomowoc WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Ordered the parts from the product discription (photo) as well as chart showing actual size. Got the parts( in two separate shipments) cut the bar to length and snapped them inot place. Bingo!

Needed to replace freezer rack

  • Customer: Carl from Bloomfield NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I had to cut the rack itself. It was too long. So make sure you have a hacksaw ready. But first look in a junk yard the rack piece is too expensive for a piece of metal

Frost in freezer, fridge not cold

  • Customer: Bob from Pinole CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

We are moving out of military housing and we had to replace the freezer door holder before we moved or we would have had to pay for the wholr refrigerator

  • Customer: Christopher from Fort Sill OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
We replace the end pieces to hook the holder back on the door.

Freezer built ice, fridge not cold enough and running constantly.

  • Customer: LUIS from CENTENNIAL CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.
All Instructions for the TRT18GRED0
76-90 of 177