Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TRT17CRAW1 > Instructions

TRT17CRAW1 Tappan Refrigerator - Instructions

All installation instructions for TRT17CRAW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TRT17CRAW1
76-90 of 179
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator keeps frosting up and not cooling

  • Customer: Marvin from Pima, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Refrigerator started frosting up and running all the time.I'd defrost it and it would frost up again in about a week.The timer seems to be work so I just guest it mite be the Defrost Thermostat.I removed the duck in the center and back panel in the freezer compartment defrosted it and switched Thermostats and replaced panel and duck, going to lower compartment of the refrigerator.So far it seems to be working a little more time while tell.

Cross bar end caps were broken.

  • Customer: Charles from Fox Island, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I put the end caps on the cross bar and reinstalled it in the fridge. Easy job.

frezzer iceing over and not cooling the refrigerator

  • Customer: Marcus from Pine Hill, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.

No freezing or cold in either freezer or refridgerator - compressor did not run.

  • Customer: George from Sunnyvale, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

Door shelf end cap broke

  • Customer: Judith from Lewisburg, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
We just put the new end parts into the door and then placed the bar inside the caps. We had contacted our appliance dealer at least three times to get parts for us but to no avail. A friend told me about your website and the rest was history ----- and easy. Thank you.

coil Iceing up

  • Customer: Thomas from Stuart, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .

Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.

  • Customer: Larry from Newton, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 4 people found this instruction helpful
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

plastic brackets that hold rack were broken in refrigerator door

  • Customer: Mary from Baltimore, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
The new parts just popped right into the holes and the door now has two shelves again.

Freezer okay, but fridge was warm

  • Customer: brad from minneapolis, MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Website was great!

The defrost timer was right in front. 2 minutes and a screwdriver and I had it replaced.

To replace the thermostat, I had to take out the back panel, defrost it and then install the new part. the only problem was that the heatshrink tubing they sent was too large. Otherwise, it worked great.

Evaporator In Freezer Freezing Up, Fridge Warm

  • Customer: DONALD from MECHANICSVILLE, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Removed shelf brackets to allow the removal of the evaporator sheetmetal cover. Unpluged wires to thermostat ,removed defrost timer and plugged in new timer,(front left lower kick panel). Cut and resoldered wires to new thermostat reinstalled thermostat and cover in reverse order. I knew what parts I needed and how to repair the unit,however your customer comments were spot on and would help anyone perform a successful repair (you provide a helpful service for the public)

broken shelf bar with missing end brackets.

  • Customer: Robert from Oconomowoc, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Ordered the parts from the product discription (photo) as well as chart showing actual size. Got the parts( in two separate shipments) cut the bar to length and snapped them inot place. Bingo!

The door shelf retainer bar was too long, 6" to 8"

  • Customer: Jane from Hudson, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I measured the width I needed and used a handsaw to cut it the proper length. Then I snaped the pieces in and it was a perfect fit.

freezer worked frig was warm. Ice maker is still not working

  • Customer: steve from Kirkland, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall

Frost in freezer, fridge not cold

  • Customer: Bob from Pinole, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

bottom door shelf, both end caps broken off

  • Customer: Lance from Blaine, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
put both end caps on metal guard,put back on door,push down to lock into place. 30 second repair,
All Instructions for the TRT17CRAW1
76-90 of 179