Models > TRT16PNCD0

TRT16PNCD0 Tappan Refrigerator - Overview

Get Parts and Repair Help for TRT16PNCD0

If you know the refrigerator repair part you need, you can browse the list of all parts on the TRT16PNCD0, or you can search by name or part description. You can also find your part by where it is located on the TRT16PNCD0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for TRT16PNCD0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$17.07

Defrost Timer - 60Hz 120V

This defrost timer will cycle for thirty minutes after every eight hours of run time.

Order within the next 4 hrs and your part ships today!
$3.64

Door Shelf End Cap - Left or Right Side

This end cap can be used for the right or left side of the refrigerator door shelf or the freezer door shelf.

Order within the next 4 hrs and your part ships today!
$3.33

Door Shelf End Cap - Left or Right Side

It can be used for either the right side or the left side of some refrigerator door shelves.

Order within the next 4 hrs and your part ships today!
$25.00

Run Capacitor

This part is attached to the compressor. It helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

Order within the next 4 hrs and your part ships today!
$12.91

Defrost Thermostat

This limiter thermostat cuts out when the temperature inside your refrigerator reaches 55 degrees Fahrenheit and kicks back in when the internal temperature drops to 20 degrees Fah...

Order within the next 4 hrs and your part ships today!
$42.04

Door Shelf Retainer Bar - Cut to Fit

This is a white cut-to-fit door shelf retainer bar.

Order within the next 4 hrs and your part ships today!
$24.12

Evaporator Fan Motor Kit

This motor runs the evaporator fan in your refrigerator. It is mounted on the center hub and has three lead wires terminals. This motor rotates in a clockwise fashion. Its shaft ha...

Order within the next 4 hrs and your part ships today!
$3.59

Crisper Drawer Cover Support

Order within the next 4 hrs and your part ships today!
$24.55

Evaporator Fan Blade

Order within the next 4 hrs and your part ships today!
$6.13

Screw

This screw is sold individually.

Order within the next 4 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Fridge got warm and freezer coils were frosted

  • Customer: Stephen from Warrington PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 213 of 247 people found this instruction helpful
Fridge is a side by side. The freezer is pretty narrow for a guy with wide shoulders.

Pulled plug.

Had to remove bottom drawers then used nut driver to remove screws closest to back wall in drawer runners. Once the back screws were removed the runners could be swung up or down out of way so back cover could be removed.

On... read more

Noisy fan

  • Customer: Jordan from Maumee OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 84 of 94 people found this instruction helpful
1. Removed the 7 nuts using the nut driver from the freezer back panel inside the freezer.
2. Remove the back panel. The evaporator motor and fan are located above the coils.
3. Unplug the wiring harness.
4. Remove the two gold mounting screws holding the motor and fan in place.
5. Remove the motor and fan including the brackets.
6. ... read more

Clicking sound then within a minute clicking again, not cooling.

  • Customer: Melvin from Semmes AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 62 of 71 people found this instruction helpful
UNPLUG REFRIGERATOR. Carefully remove relay from the side of the compressor. You shouldn't need a tool to do this, if it is hard you can gently pry the edge with a flat head screw driver just to loosen. Unplug white and red wires from relay, noting that the white wire goes in the hole with a #2 stamped beside it. Shake old relay, if it rattles like a baby r... read more