Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TRT15DRAW1 > Instructions

TRT15DRAW1 Tappan Refrigerator - Instructions

All installation instructions for TRT15DRAW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TRT15DRAW1
76-90 of 178
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refer iced up and would not keep the bottom cool. It was 70 Farenheit inside.

  • Customer: Larry from Newton, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 4 people found this instruction helpful
I simply removed 4 screws holding the casing and then 2 more holding the timer. It was very easy. I then replaced the timer by unplugging and plugged the new one in. I replaced all the screws and the job was done. Less than 30 minutes. I was very impressed with the shipping time. When I ordered the part, I had it the next day.

plastic brackets that hold rack were broken in refrigerator door

  • Customer: Mary from Baltimore, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
The new parts just popped right into the holes and the door now has two shelves again.

Freezer okay, but fridge was warm

  • Customer: brad from minneapolis, MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Website was great!

The defrost timer was right in front. 2 minutes and a screwdriver and I had it replaced.

To replace the thermostat, I had to take out the back panel, defrost it and then install the new part. the only problem was that the heatshrink tubing they sent was too large. Otherwise, it worked great.

Evaporator In Freezer Freezing Up, Fridge Warm

  • Customer: DONALD from MECHANICSVILLE, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Removed shelf brackets to allow the removal of the evaporator sheetmetal cover. Unpluged wires to thermostat ,removed defrost timer and plugged in new timer,(front left lower kick panel). Cut and resoldered wires to new thermostat reinstalled thermostat and cover in reverse order. I knew what parts I needed and how to repair the unit,however your customer comments were spot on and would help anyone perform a successful repair (you provide a helpful service for the public)

W/O End Caps Nothing Will Stay On Shelf

  • Customer: Kimberly S from Calimesa, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
First, I should tell you I break more things than I fix by trying to install wrong or tightening until broken. It may seem real easy to to put end caps on but there was a suprised look on my wife's face when she watched me put them on the first time. She made me some chocolate chip cookies to celebrate. I ordered the parts and received them the next day. I shopped local and and was quoted up to five times the price nobody had them in stock.

Broken End Caps On Center Door Shelf

  • Customer: THOMAS from STATEN ISLAND, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I removed the broken end caps by hand. They snap in to the center retainer bar. I ordered replacement parts from part select on their website. New end caps arrived in a couple of days. I installed new caps. No tools needed. Great service by part select. Thank you tm staten island ny

Refrigerator keeps frosting up and not cooling

  • Customer: Marvin from Pima, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Refrigerator started frosting up and running all the time.I'd defrost it and it would frost up again in about a week.The timer seems to be work so I just guest it mite be the Defrost Thermostat.I removed the duck in the center and back panel in the freezer compartment defrosted it and switched Thermostats and replaced panel and duck, going to lower compartment of the refrigerator.So far it seems to be working a little more time while tell.

One broken retainer bar, and 4 broken brackets

  • Customer: Richard from El Cajon, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 2 of 7 people found this instruction helpful
cut the retainer bar to proper lengh, put on the
end caps of both bars in question and snapped them both into place.

both end caps broke

  • Customer: Rita from Verona, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Door panel was already off. Took off broken caps, placed new ones on & put back on door.

Refrigerator was not cooling and the motor was running constantly

  • Customer: Anil from Somerset, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 1 people found this instruction helpful
Having tried PartSelect.com before, I was very comfortable with the process. Input my symptoms and the feed back I received was that one of the 2 things (Defrost Timer or Defrost Thermostat)might need replacement. Since the cost was not much and over night shipping would cost more than the product, I decided to order both the parts. Changing parts was a breeze. The instructions posted by others on your web site were very easy to follow. You guys save me a bundle every time I have any thing going worng with any of my appliances.

broken shelf bar with missing end brackets.

  • Customer: Robert from Oconomowoc, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Ordered the parts from the product discription (photo) as well as chart showing actual size. Got the parts( in two separate shipments) cut the bar to length and snapped them inot place. Bingo!

The door shelf retainer bar was too long, 6" to 8"

  • Customer: Jane from Hudson, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I measured the width I needed and used a handsaw to cut it the proper length. Then I snaped the pieces in and it was a perfect fit.

freezer worked frig was warm. Ice maker is still not working

  • Customer: steve from Kirkland, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Removed two screws to get to defrost time pull panel down remove two screws holding time and reinstall

bottom door shelf, both end caps broken off

  • Customer: Lance from Blaine, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
put both end caps on metal guard,put back on door,push down to lock into place. 30 second repair,

Freezer built ice, fridge not cold enough and running constantly.

  • Customer: LUIS from CENTENNIAL, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
Removed front low grill, removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. Reversed process to install new timer.
All Instructions for the TRT15DRAW1
76-90 of 178