Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TRT15DRAW0 > Instructions

TRT15DRAW0 Tappan Refrigerator - Instructions

All installation instructions for TRT15DRAW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TRT15DRAW0
61-75 of 178
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Shelves wobble and gasket leaked..

  • Customer: Carla from Sumter, SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
I replaced the shelf end caps in the shelves of my fridge and I also replaced the gasket around the door.

Every time I would open the door, things would fall out because the shelves were giving, because the end caps were broken. Once I got the new ones, I was amazed that these parts are still available and that they lock right in with no problem. Once you get one in, you then have to place one end of that retaining bar into that, very tightly, making sure the end is completely secure in the cap. Then you can lock the other cap to the other end, lock it into place in the door and whala! It is just that simple.


Now the gaket is another story, it is best to soak the gasket in hot water first to draw it up abit so it will be snug and also to use lubricant such as petroleum around the inside where it is going to fit to the door. This made it extremely easy to afix to my door with no problems. I am so glad for this site.. hundreds of dollars saved!!

no shelves refrigerator door

  • Customer: Nancy from Schenectady, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Needed to saw the pieces. PUrchased hacksaw.
Son sawed the pieces. Went in like a piece of cake.

end cap broke

  • Customer: Connie from Seneca, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
First I removed the broken end caps. I placed the new end cap onto the shelf bar and snapped the end cap into the holding slot on the door interior. Took about 5 minutes. Very easy.

For years we opened the refridgerator door and the things fell off the bottom shelf.

  • Customer: Anne from Prudence Island, RI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
We ordered end pieces for the shelf holder, attached them to the long piece and snaped them into the door. Three minutes to open the box, attach, and close the door. A less than 20 dollar repair and success!

No freezing or cold in either freezer or refridgerator - compressor did not run.

  • Customer: George from Sunnyvale, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 2 people found this instruction helpful
Traced issue to defrost timer ( burned compressor & element contacts). This unit is mounted next to the temperature adjustment control in the refridgerator area - right in front. Removal of plastic cover provided easy access to the timer. Unit unscrews from the mounting then unplugs. Installation is reverse of removal.

Defroster didn't work

  • Customer: George from Eatonville, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Ordered a new defroster timer and replace old one. It works just fine. A $35 repair vs a $500 new appliance.
Cool.
GWE

Bottom shelf (beverage shelf, large bottles, etc.) was unuseable because the plastic end caps were cracked. The metal shelf bar was intact though.

  • Customer: Stephen from Springfield Gardens, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
We have a wonderful Kelvinator refrigerator. It has served us tirelessly for more than 15 years - and looks as good as new! (We frequently clean it out and clean the interior and exterior, to keep it looking and smelling clean)

Replacement of the end caps and shelf was very easy!

The broken end caps were removed (missing for years), and it became one of those small projects that one never gets around to. I finally took down the model number and looked online for it. Google or Yahoo (can't remember which) pointed us to you site. I was SHOCKED to see that the parts were still available! I called your friendly customer order line and had a very pleasant experience placing the order. The BIGGEST shock came when the parts arrived THE NEXT DAY!! Just in time for Thanksgiving! You are AWESOME!

The Repair:

Easy as pie. The end caps simply snap into place. I did the left side first, then carefully inserted the metal bar, which is supported by the two end caps. Next I snapped in the right side cap - DONE. It took longer to clean the bar up, than it did to replace the caps!

The Results:

The bottom door shelf is now useable again. We can place 2 liter beverages and juice containers on the door, where they belong! My wife cheered and commented, "The refrigerator is no longer an eye sore when I open it!" :-)

Thank you Parts Select!!!!

Frost in freezer, fridge not cold

  • Customer: Bob from Pinole, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

my refrigator did not have the lower door shelf retainer bar

  • Customer: Karen from Kearny, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
the repair went fast and easy. my boyfried measured the retainer bar, cut it with the hack saw installed the right and left side door shelf end cap and inserted the door shelf retain bar. the door looks great. would highly recommend your website and customer service. thanks again.

Freezer coils kept freezing over.

  • Customer: Kyle from Porter, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 3 people found this instruction helpful
1. Turned off the cooling cycle and unplugged the refrigerator.
2. Removed all of the shelving and bottom basket.
3. Removed rear covering in the freezer section.
4. If frosted over, manually defrost coils with hairdryer.
5. Located original thermostat and after marking the wire locations cut the wires and removed the Thermostat.
6. Connected matching wires using a lighter to melt the wires together. Wrapped repaired wires with electricians tape.
7. Unable to install the thermostat in the recommended location (freezer is a tight fit) the new part was installed at the original location.
8. Replaced the rear cover and shelves.
9. Plugged in the refrigerator and set the cycle back to cooling.
10. Monitored freezer coils couple of days/weeks depending on how fast they freeze over (slots at bottom of cover) to validate if problem solved.

Tenants broke bent the retainer bar and broke end caps

  • Customer: Richard from Palm Springs, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 3 people found this instruction helpful
The parts were sent out fast, but the wrong retainer bar.
My apartment bldg is in another state, by the time I got up to my apartment bldg to do the repair several weeks had passed and i lost the bill to get a refund and now I have a $40.00 strip of metal sitting in my garage
So the fix time would have been 15 minutes had I received the correct part.

Cross bar end caps were broken.

  • Customer: Charles from Fox Island, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I put the end caps on the cross bar and reinstalled it in the fridge. Easy job.

frezzer iceing over and not cooling the refrigerator

  • Customer: Marcus from Pine Hill, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Just removed the two screws and unpluged it.
Then I pluged the new one in and replaced the screws. It runs like a brand new reffrigerator.
Thanks for the fast delevery. Will do busness with you in the future.

Door shelf end cap broke

  • Customer: Judith from Lewisburg, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
We just put the new end parts into the door and then placed the bar inside the caps. We had contacted our appliance dealer at least three times to get parts for us but to no avail. A friend told me about your website and the rest was history ----- and easy. Thank you.

coil Iceing up

  • Customer: Thomas from Stuart, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
took 4 screws out of the discharge vent on top of the refrigerator section and unpluged the wiring harness and put the section on the counter and unscrewed the timer and put the new one in and reinstalled the assembly and plugged the Jack and put the 4 screws back in, and rotated the timer and put it on defrost removed the back and check the heaters and drain .
All Instructions for the TRT15DRAW0
61-75 of 178