Models > TRS20WRHW3 > Instructions

TRS20WRHW3 Tappan Refrigerator - Instructions

All installation instructions for TRS20WRHW3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TRS20WRHW3
61-75 of 259
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

wOULD NOT DISPENSE ICE FROM ICE TRAY

  • Customer: WILLIAM from KERRVILLE TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 12 people found this instruction helpful
DID NOT REPLACE ITEMS ORDERED BUT REPAIRED ITEM (DRIVE BLADE ) AND REINSTALED REPARED PARTS UNTIL THEY FAIL COMPLETELY. i KNOW THEY WILL IT IS JUST A MATTER OF TIME.
BUT SEEING THAT I AM 72 YEARS OLD IT WAS NOT THAT DIFFICULT TO DO THE REPAIRS, JUST LIFT UP ICE BIN AND PULL OUT, THAN TAKE IT APPART REMEMBERING HOW EACH PART FACED AND IN WHAT ORDER.
THANK YOU FOR GIVING ME THE PARTS MANUAL AND NUMBERS OFF INTERNET .
SINCERELY YOURS

Freezer too cold

  • Customer: Curt from Maple Grove MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 3 people found this instruction helpful
Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.

Great resource and service, thank you.

coils freezing refrigerator not cooling

  • Customer: Else from Plant City FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 6 people found this instruction helpful
The defrost timer is located under the freezer side behind the lower plastic cover. Very simple, just 2 screws and a plug, and your done.

The thermostat requires removing the lower drawers in the freezer and unscrew the back side of the rails and let them hang over to get access to the lower cover on the back of the freezer. Once the panel is off you will be able to see the thermostat. From there you just remove the thermostat from the clip, cut the 2 wires, splice in the new thermostat and re install using the new clip and your done!!

This was my first time and it was really simple. I had a local repair shop quote me $375.00 . I did it myself for under 50.00 shipped to my door..

Stopped making ice.

  • Customer: WILLIAM from KERRVILLE TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 4 people found this instruction helpful
Had to reach right hand to top of ice maker to locate hex head screws by feel, then place nut driver onto hex head by feel and then unloosen screws with lft hand ,a couple of turns, enough to lift ice maker off screws.
Replace new icemaker onto screws and tighten screws. The only problem incountered was the location and availability of having to feel with both hands to fit nut driver onto the screws.(could not see with my eyes because front of ice maker blocked view. )

Common drawer slide cracked

  • Customer: Michael from New Carlisle OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
It was a snap. Literally. all I had to do was snap and slide the front off the broken drawer and slide and snap it onto the new.

Easy Fix

  • Customer: Damien from Oneonta NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Was really basic, simply slide off the old caps, slide on the new ones, put the shelf back where it goes, push down lightly so as to not snap the new caps, and viola, complete. No more than 2 minutes worth of work. Great part at a great price, shipping was more than the part itself so I bought 2 of each. Only problem I ran into was that I ordered the top shelf caps instead of the bottom the first time, so I had to reorder.

Freezer frosted up, refrigerator compartment heated up

  • Customer: James from Hanover ME
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
I removed the housing at the top of the refrigerator compartment that contained the reefer light and temperature adjustment knob. This required a small nut-driver. Inside, I found the old defrost control, unplugged it, unscrewed it with a Phillips screwdriver, and replaced it with the replacement part. Then I replaced the housing to its original position.

Rust had corroded Front Plate and Drive Blade

  • Customer: Calvin from Massillon OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 8 people found this instruction helpful
Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.

Rust on Front Plate and Drive Blade

  • Customer: Wayne from Westford MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 8 people found this instruction helpful
Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

A 2" x 4" section on the bottom of the ice container bucket broke out.

  • Customer: David from Owensboro KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Simply detached the old ice container by removing four screws and removing one screw holding the lever onto the bottom of the container. A bit of advice; make sure you note how the spring is attached to the lever before removing the screw. It took me a bit to determine how the spring activated the lever when I was reattaching it to the bottom of the container. Also, double check your order before you finalize it. I must have inadvertently hit the item twice so I received two of them. This resulted in me having to return one item and paying for extra shipping both ways. I received the part within two days of my order. It was a very fast turn-around. Also, when I realized that I received two parts and had to call to explain the situation, I found the person on the phone to be extremely helpful and courteous. She sent me information regarding how to return the product and didn't ridicule me once for my stupidity.

Freezer icing up and refrigerator section not cold

  • Customer: Les from Fenton MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
Removed four screws for cover on refrigerator temperature controls, unpluged old timer and pluged in new timer. Replaced cover and screws.

ICE MAKER STOPPED MAKING ICE

  • Customer: PERRY from LOWER BURRELL PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 5 people found this instruction helpful
REMOVED POWER , UNPLUGGED WIRES AND

2 SCREWS THEN REVERSED THE PROCESS

1 HOUR LATER FIRST BATCH OF CUBES DROPPED INTO BIN

There was a hole in the plastic bin where ice fell through to the freezer.

  • Customer: Thomas from Niceville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
I removed the screws that held the the ice dispencer from the bin. I than removed three screws from the bottom of the bin. I put the new plastic piece on the end of the spiral piece that
pushes the ice. I inserted the spiral piece back into the hole. I than screwed the ice dispencer
to the bin and re-inserted it back in the refrigerator.
It took me about 5 to 10 minutes. It's really easy!

ICE WOULD NOT DISPENCE

  • Customer: Jerry Baten from Pampa TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 8 of 20 people found this instruction helpful
TOOK THE ICE STORAGE BIN OUT. TOOK THE UNIT APART,AND DISAMBLE THE AUGAR UNIT. ORDERED PARTS FROM MANUFACTURE, WHICH ARRIVED IN TWO DAYS. AS SOON AS I GOT THE PARTS, I REASSAMBLED IT. WORK PERFECT. GOOD JOB!

crusher housing cracked

  • Customer: Adam from Clayton NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
Removed ice tray, disassembled ice tray assembly and crusher housing making sure to note the spring location, spring etc, installed new plastic housing making sure to reinstall the spring properly and the fixed crusher blade into the notch cutout., reassembled ice tray.
All Instructions for the TRS20WRHW3
61-75 of 259