Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TRS20WRHW1 > Instructions

TRS20WRHW1 Tappan Refrigerator - Instructions

All installation instructions for TRS20WRHW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TRS20WRHW1
76-90 of 274
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The refrigerator wasn't cold enough.

  • Customer: John from San Diego, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
I removed the plastic shroud on the ceiling of the refigerator, unscrewed and unplugged the old defrost timer, and replaced it with the new one. I reinstalled the shroud with the new timer installed.

wOULD NOT DISPENSE ICE FROM ICE TRAY

  • Customer: WILLIAM from KERRVILLE, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 13 people found this instruction helpful
DID NOT REPLACE ITEMS ORDERED BUT REPAIRED ITEM (DRIVE BLADE ) AND REINSTALED REPARED PARTS UNTIL THEY FAIL COMPLETELY. i KNOW THEY WILL IT IS JUST A MATTER OF TIME.
BUT SEEING THAT I AM 72 YEARS OLD IT WAS NOT THAT DIFFICULT TO DO THE REPAIRS, JUST LIFT UP ICE BIN AND PULL OUT, THAN TAKE IT APPART REMEMBERING HOW EACH PART FACED AND IN WHAT ORDER.
THANK YOU FOR GIVING ME THE PARTS MANUAL AND NUMBERS OFF INTERNET .
SINCERELY YOURS

Stopped making ice.

  • Customer: WILLIAM from KERRVILLE, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 4 people found this instruction helpful
Had to reach right hand to top of ice maker to locate hex head screws by feel, then place nut driver onto hex head by feel and then unloosen screws with lft hand ,a couple of turns, enough to lift ice maker off screws.
Replace new icemaker onto screws and tighten screws. The only problem incountered was the location and availability of having to feel with both hands to fit nut driver onto the screws.(could not see with my eyes because front of ice maker blocked view. )

No Ice !

  • Customer: Kevin from Bridgewater, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 4 people found this instruction helpful
Real simple repair..just backed off the two 1/4" hex bolts holding the ice maker to the wall of the fridge,(a little tricky since you can't see them),unclipped the electrical doo hickey. I re-clipped the electrical do hickey of the new ice maker, hung the ice maker on the bolts and then re-tightened them. However,still no ice,my problem was the water valve on the back of the fridge behind the cardboard. Although it was still giving H2O thru the door it was not allowing water to flow to the ice maker. I reccommend pouring some water into the ice tray of the ice maker. If it makes ice and dumps it in to the holder, your ice maker is OK. If it turns out to be your water valve, that fix is easy as well. I HIGHLY reccommend watching the "fix it" video associated with that part. That repair also took less than 15 minutes. Good Luck! KC Bridgewater,NJ

Rust on Front Plate and Drive Blade

  • Customer: Wayne from Westford, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 10 people found this instruction helpful
Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

only freezer was cold, frig warm

  • Customer: Edward from Middletown, DE
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 3 of 4 people found this instruction helpful
removed all items from frig.. removed shelves, loosened one screw on each slide bracket and moved them down and out of the way of the rear panel....removed 6 screws in rear panel...removed all ice on coils with a heat gun...located defrost stat, replaced...crimped wires...re-installed rear panel and shelves! On left side of frig. in front bottom..located defrost timer..removed trim piece, loosened 2 screws....removed and replaced defrost timer...plugged in the frig. and it started!!!!

Fridge not cooling

  • Customer: WESTLEY from HATTIESBURG, MS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 3 of 5 people found this instruction helpful
My fridge side had warmed up to 70 degrees but the freezer side was still cold. The coils inside had iced up. After thawing with a hair dryer, it froze back after another week. I removed the old defrost thermostat and wired the heater strip directly and turned on the defrost timer. It began melting the ice so that ruled out the heater strip being bad. I couldn't get a reading with my ohm meter on the defrost thermostat so I took a chance and bought the part. Installation was a breeze and it fixed the problem.

Ice Maker Stopped Making Ice

  • Customer: PERRY from LOWER BURRELL, PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 3 of 5 people found this instruction helpful
Removed power , unplugged wires and 2 screws then reversed the process 1 hour later first batch of cubes dropped into bin

Ice maker stopped working

  • Customer: Joseph from Seal Beach, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
First I determined the icemaker was the problem when it was no longer calling for water. You can hear that "whistle" for 6-7 seconds when it calls for water. Anyway, replacement was a piece of cake, but did not entirely fix my problem. I also had to flush the lines to the soloniods that allow water to flow through the filter and into the water storage tank because it was cloggged with a little piece of plastic.

Fan not running.

  • Customer: chester from Oak Lawn, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
removed old fan and replaced it.3 screws and plug.Always unplug appliance when working on it.

Frost in freezer, fridge not cold

  • Customer: Bob from Pinole, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
From most posts I've read, the defrost timer was the culprit so I blindly ordered one. Easy install but did not fix the problem so I broke out the ohm meter. The only other 2 items it could be all tested good with my meter so I bypassed the defrost thermostat (per forum help...actually quite easy)and it defrosted fine, which told me I needed a new defrost thermostat. Installed fairly easy and problem gone.

Ice not depensing, Door rubbing

  • Customer: Dominick from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
Remove Ice dispenser from freezer, removed all screws that hold auger & blades, by remove ring & washer. Removed blades replaced broken drive blade and re-assembled. Removed ref. door install new bearing at bottom re-installed door. Both job very easy.

shelf door end caps broke off

  • Customer: Stephen from Strongsville, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
I would like to say first PARTS SELECT is the best everyone was more than helpful My main problem was the model no.on the frig was the wrong number so with that now being a known fact the people on the phones were very helpful in finding the parts I needed... my proproblem was the parts were alittle different than OEM. thats were the HOT WATER comes into play after talking with factory Tech because the clip end were alittle smaller so hot water & soap would them more flexible to slip into place
So THANK YOU again
Steve Kovacs

refrigerator shelf guard kept falling off, causing everything to come crashing down

  • Customer: Kathryn from Anadarko, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Simply popped the new end caps into place with the old guard and now it is tight and secure. Easy Peasy. Of course all this is after the operator at PartSelect ordered the right part for me; I had ordered the freezer door end cap, not what I wanted. I received the correct part the very next morning. Returning the wrong part was a breeze too.

Ice maker wasn't making ice

  • Customer: Scott from Grayson, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 3 people found this instruction helpful
Occasionally, we'd get one batch of ice cubes and a frozen lake of water in the bottom of the ice tray.

The installation was easy and I won't bother duplicating the comments of others who have installed this part.

One word of caution: The ice maker contains a heating element on the bottom. That element is apparently live even when the ice bar is in the upper (off) position. When I unscrewed the old ice maker and went to lift it off the bolts, I severely burned my finger on the bottom of the old ice maker because apparently I started the repair in the middle of the heating cycle.

I highly recommend that you unplug the ice maker entirely before doing the replacement and gingerly ensure that the unit isn't hot before touching it. You'll save yourself a nasty burn.
All Instructions for the TRS20WRHW1
76-90 of 274