Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TMT116E1B0

TMT116E1B0 Tappan Microwave - Overview

Get Parts and Repair Help for TMT116E1B0

If you know the microwave repair part you need, you can browse the list of all parts on the TMT116E1B0, or you can search by name or part description. You can also find your part by where it is located on the TMT116E1B0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your microwave. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$20.62

Grease Filter

If you are having trouble cleaning out your grease filter, or if it is damaged to the point of no return, maybe it is time to replace it. The grease filter is a ventilator that tra...

$32.16

Relay Switch

The relay switch may also be known as the door micro switch and is a part for your microwave. The function of this part is to monitor the door latch and communicate whether the door latch is open or closed to the electronic control board. Before making this repair, you will want to make sure to unplug your microwave and discharge the capacitor. Your microwave capacitor is able to store electricity in large quantities even after it has been unplugged. The most common reason for replacing your relay switch is if the microwave will not turn on but your timer still runs..

$16.44

Light Bulb - 20W

This 20-watt lightbulb is most commonly found in the microwave. The lightbulb brightens the interior of the microwave while it is running so you can keep an eye on the food while i...

$34.24

Turntable Motor

This turntable motor is used in microwaves. This is what rotates the glass tray so that your food is heatied evenly. The specs for this synchronous motor are 120 Volts, 60Hz, 3rpm, and 2.1 Watts. It features two 3/16-inch male spade terminals, which is what attaches to the internal wiring of your appliance. The motor also includes mounting holes; there are two mount holes on either side of the part. This replacement motor is approximately two inches in diameter, and it is sold individually. Before you attempt this repair make sure you unplug your microwave.

$6.69

SCREW-UNIFIED

$6.67

SCREW

$79.07

Roller Support

$57.53

FUSE

$44.07

Micro Switch with Line Fuse

$8.82

SPRING

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Timer would run but the microwave won't start

  • Customer: Tim from Chicago, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 73 of 112 people found this instruction helpful
I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up. read more

Turntable stoped working

  • Customer: steve from New Bern, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 26 of 29 people found this instruction helpful
Removed the 3 screws to drop the lower panel and, removeed the turn table plate and ring. Then removed the 2 screws holding the motor, the 2 wires attached to the motor and removed the old motor.Replaced the new motor in the reverse order. DO NOT FORGET TO UNPLUG THE MICROWAVE FIRST. read more

microwave wouldn't turn on but timer worked.

  • Customer: Steve from Moorhead, MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 31 of 46 people found this instruction helpful
was told buy a repair person to check the door micro switches as it was a common problem. removed the top plastic air grill to get access to the screw that holds in place the control cover. After unplugging the unit, i took out the (2) screws that held in the switches and removed them (3). One switch was a bit melted so i tested it with a 12 volt battery and... read more