Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TGF657BCB2 > Instructions

TGF657BCB2 Tappan Range - Instructions

All installation instructions for TGF657BCB2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TGF657BCB2
166-180 of 194
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

upper oven would light up but took awhile

  • Customer: robert from des plaines, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
disconnect electrical power to oven , removed face plate to where the igniter connections were. lift cover that is over the igniter in oven, remove igniter from burner, attach ner igniter to burner and route wires inside cavity where connections are. cut connector from old igniter leaving enough wire to splice to new igniter, strip wire and connect using wire nuts, put everything back together and test

oven took very long time to ignite.

  • Customer: Ronald from Keymar, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
first we went online to see if others had experienced the same problem, and what they did to fix it. ordered part to arrive within three days. husband removed connecters from old igniter and spliced them onto new one. We felt it should have come with connecters. set burner with new igniter in place, and it worked...Yay! just in time for Thanksgiving turkey!

Igniter glowed but slow or no oven lighting

  • Customer: JAMES from Harrison, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the igniter.

oven wouldn't light

  • Customer: Donna from Trinidad, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
using socket set removed old ignitor,replace with new one and secured using the socket set. The oven lite right up.Service was A1. I ordered on Friday evening and the part was delivered on Monday. Thank you.

Oven would not light

  • Customer: Edward from Pent Water, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Put a new ignighter in the oven I also would like to commend PartSelect for the fast service on the part i ordered it one day and recieved the part the nexted day i would recommend you any time

Oven lights intermittently, smell of gas

  • Customer: Robert from Lakewood, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Model# GLGF366ASD range
Turned off breaker
Removed oven door (see gas range manual for procedure)
Removed storage drawer on bottom of range.
Removed oven racks.
Removed oven bottom panel (2 screws in back of panel)
Removed oven shield (screw on left and right front of panel & nut in middle of panel)
At this point igniter was exposed
Removed igniter by removing the 2 self tapping screws securing igniter.
Note: threads on both screws stripped during removal, requiring both
screws to be cut off for removal.The stripping of threads of these screws
is probably normal due to the heating and cooling of the oven during
operation, making the threads on the screws brittle.
Marked the top wire on the igniter with a black sharpie
Cut both wires as close to the old igniter as possible.
Cut wires on new igniter about 10" long.
Connected new igniter with wire nuts (provided) making sure to connect wire from top of igniter to wire marked with sharpie.
Installed new igniter using 2 new #8x1/2" self tapping screws.
Pulled excess wire & wire nut connections down into the back of the storage drawer area making sure wires were resting on flanged area of panel.
Reinstalled oven shield, panel, racks, storage drawer, and oven door.
Turned breaker back on.
Oven works great.
Note: self tapping screws should be provided

Gas will not start

  • Customer: Paresh from La Palma, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged the range. Opened the range by removing the burners. Removed exiting spark module then installed new one. Just make sure the four plugs are correct.

Igniter not drawing enough volts to open safety valve.

  • Customer: Christopher from Oakmont, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the oven drip pan and removed the old igniter and cut wires and used the supplied wire nuts and replaced the old part turned the oven on and it ignited.

not heating as setting reads

  • Customer: Debra from Miramar Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
watched u tube sent by your company, opened back of oven,removed sensor,checked w/ohm meter,ordered part, replaced sensor,replaced back on oven, DONE! works like new amazing help I was given by your staff! I was quoted over $200.00 to come to my house,ck.,fix, and part replaced. My cost was $50.00 + shipping of $7.00. Thank you guys!

Gas oven light off time long, strong gas smell in house from long light off time. Oven would not control desired temperature.

  • Customer: Richard from Rockford, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Disconnected electric power. Removed oven floor and flame spreader to access igniter. Spliced replacement igniter to original igniter connector plug wires. Mounted new igniter and reinstalled flame spreader and oven floor. Reconnected electric power and checked oven operation. Oven light off time was within 1 minute and oven temperature controlled to all settings up to 450 degres.

Oven took a long time to light, did not stay lit

  • Customer: Carol from Campus, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very Easy. Part arrived in less than 48 hours of ordering. Followed the directions included with part and referenced the information posted here.I have no mechanical talent and was able to install the part without difficulty.

Gas oven would not light

  • Customer: Steve from Fredericksburg, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I checked the igniter resistance with an ohm meter. It read about 350 ohms. Voltage across igniter leads with igniter removed was 120 volts when the oven temperature control was turned on, so I knew the gas control and thermostat were ok. The new igniter has a resistance of about 220 ohms, so the difference was apparently enough to keep the oven from turning on. This is the second igniter I've replaced in this 20 year old oven, the first bad igniter had open resistance, obviously since it was visibly cracked. The repair went very fast, directions were great.

would glow but would not ignite

  • Customer: charles from Mount Prospect, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Turned off power removed racks removed bottom panel removed flame distribution plate removed igniter i didn't use -the wire nuts 'the wires on the new part were more than long enough so i installed new stake ons reveresd disassembly process turned power back on and now it works great with a factory look

Left hinge broke in pieces

  • Customer: Marilyn from Yonkers, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
First I read other comments here; then checked youtube.com to see if there was a video - there was! Easily removed the stove door and the storage drawer to access the spring. Removed the spring and used screwdriver to remove 2 of 3 screws - third had a nut on back which required removal of the decorative panel next to the door. After applying Liquid Wrench, was able to use vise-grip to remove last bolt. Inserted new hinge, attached the spring to hinge and stove frame then inserted the 3 screws. Reattached the decorative panel and was done. Repklaced a hinge, not a stove!!!

no flame on broiler or oven

  • Customer: david from coalinga, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replaced the ignitor switch, umplug oven turn off gas. removed racks unscrewed two screws in back of oven (inside of oven), removed bottom piece of oven, one screw for broiler cover removed, then two screws for ignitor, cut wires peeled off some excess covering, twisted the new ignitor to wires covered with attached cap tightly replaced two screws in ignitior, replaced one screw in broiler cover, two screws for bottom cover, replaced racks, pluged in turned gas and turned on stove ignitor lit up and started oven broiler, now i can cook again.
All Instructions for the TGF657BCB2
166-180 of 194